XC3S100E-5TQ144C Xilinx Inc, XC3S100E-5TQ144C Datasheet - Page 122

• Manufacturer Part Number: XC3S100E-5TQ144C
• Description: FPGA Spartan®-3E Family 100K Gates 2160 Cells 657MHz 90nm (CMOS) Technology 1.2V 144-Pin TQFP
• Manufacturer: Xilinx Inc

Specifications of XC3S100E-5TQ144C

• Package: 144TQFP
• Family Name: Spartan®-3E
• Device Logic Cells: 2160
• Device Logic Units: 240
• Device System Gates: 100000
• Number Of Registers: 1920
• Maximum Internal Frequency: 657 MHz
• Typical Operating Supply Voltage: 1.2 V
• Maximum Number Of User I/os: 108
• Ram Bits: 73728
• Re-programmability Support: Yes

DC and Switching Characteristics
Single-Ended I/O Standards
Table 80: Recommended Operating Conditions for User I/Os Using Single-Ended Standards
122
Notes:
1.
2.
3.
4.
5.
6.
LVTTL
LVCMOS33
LVCMOS25
LVCMOS18
LVCMOS15
LVCMOS12
PCI33_3
PCI66_3
HSTL_I_18
HSTL_III_18
SSTL18_I
SSTL2_I
IOSTANDARD
Descriptions of the symbols used in this table are as follows:
V
V
V
V
The V
For device operation, the maximum signal voltage (V
There is approximately 100 mV of hysteresis on inputs using LVCMOS33 and LVCMOS25 I/O standards.
All Dedicated pins (PROG_B, DONE, TCK, TDI, TDO, and TMS) use the LVCMOS25 standard and draw power from the V
The Dual-Purpose configuration pins use the LVCMOS standard before the User mode. When using these pins as part of a standard 2.5V
configuration interface, apply 2.5V to the V
For information on PCI IP solutions, see
PCI-X IP is supported.
CCO
REF
IL
IH
Attribute
– the input voltage that indicates a Low logic level
– the input voltage that indicates a High logic level
– the reference voltage for setting the input switching threshold
– the supply voltage for output drivers
CCO
(6)
(6)
(4)
(4,5)
rails supply only output drivers, not input circuits.
Min (V)
1.65
3.0
3.0
2.3
1.4
1.1
3.0
3.0
1.7
1.7
1.7
2.3
V
CCO
Nom (V)
for Drivers
3.3
3.3
2.5
1.8
1.5
1.2
3.3
3.3
1.8
1.8
1.8
2.5
www.xilinx.com/pci.
CCO
lines of Banks 0, 1, and 2 at power-on as well as throughout configuration.
Max (V)
(2)
3.465
3.465
3.465
3.465
1.95
2.7
1.6
1.3
1.9
1.9
1.9
2.7
IH
max) may be as high as V
www.xilinx.com
The PCIX IOSTANDARD is available and has equivalent characteristics but no
Min (V)
0.833
1.15
0.8
-
V
these I/O standards
REF
Nom (V)
is not used for
0.900
V
1.25
0.9
1.1
REF
IN
max. See
Max (V)
0.969
1.35
1.1
-
Table
73.
V
V
0.3 • V
0.3 • V
V
V
REF
REF
DS312-3 (v3.8) August 26, 2009
Max (V)
REF
REF
V
0.8
0.8
0.7
0.4
0.4
0.4
- 0.125
- 0.125
IL
- 0.1
- 0.1
CCO
CCO
Product Specification
CCAUX
V
V
0.5 • V
0.5 • V
V
V
REF
REF
REF
REF
Min (V)
V
2.0
2.0
1.7
0.8
0.8
0.7
rail (2.5V).
+ 0.125
+ 0.125
IH
+ 0.1
+ 0.1
CCO
CCO
R