STM32F407IGT6 STMicroelectronics, STM32F407IGT6 Datasheet - Page 36

• Manufacturer Part Number: STM32F407IGT6
• Description: IC MCU 32BIT 1MB FLASH 176LQFP
• Manufacturer: STMicroelectronics

Specifications of STM32F407IGT6

• Core Processor: ARM Cortex-M4
• Core Size: 32-Bit
• Speed: 168MHz
• Connectivity: CAN, I²C, IrDA, LIN, SPI, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 140
• Program Memory Size: 1MB (1M x 8)
• Program Memory Type: FLASH
• Eeprom Size: -
• Ram Size: 192K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 24x12b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Core: ARM Cortex M4
• Processor Series: STM32F4
• Data Bus Width: 32 bit
• Maximum Clock Frequency: 168 MHz
• Data Ram Size: 192 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 140
• Number Of Timers: 10
• Operating Supply Voltage: 1.7 V to 3.6 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 12 bit
• A/d Channels Available: 24
• Interface Type: CAN, I2C, I2S, SPI, UART
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-11604

Description
2.2.34
2.2.35
2.2.36
2.2.37
36/154
Analog-to-digital converters (ADCs)
Three 12-bit analog-to-digital converters are embedded and each ADC shares up to 16
external channels, performing conversions in the single-shot or scan mode. In scan mode,
automatic conversion is performed on a selected group of analog inputs.
Additional logic functions embedded in the ADC interface allow:
●
●
The ADC can be served by the DMA controller. An analog watchdog feature allows very
precise monitoring of the converted voltage of one, some or all selected channels. An
interrupt is generated when the converted voltage is outside the programmed thresholds.
To synchronize A/D conversion and timers, the ADCs could be triggered by any of TIM1,
TIM2, TIM3, TIM4, TIM5, or TIM8 timer.
Temperature sensor
The temperature sensor has to generate a voltage that varies linearly with temperature. The
conversion range is between 1.8 V and 3.6 V. The temperature sensor is internally
connected to the ADC1_IN16 input channel which is used to convert the sensor output
voltage into a digital value.
As the offset of the temperature sensor varies from chip to chip due to process variation, the
internal temperature sensor is mainly suitable for applications that detect temperature
changes instead of absolute temperatures. If an accurate temperature reading is needed,
then an external temperature sensor part should be used.
Digital-to-analog converter (DAC)
The two 12-bit buffered DAC channels can be used to convert two digital signals into two
analog voltage signal outputs.
This dual digital Interface supports the following features:
●
●
●
●
●
●
●
●
●
●
Eight DAC trigger inputs are used in the device. The DAC channels are triggered through
the timer update outputs that are also connected to different DMA streams.
Serial wire JTAG debug port (SWJ-DP)
The ARM SWJ-DP interface is embedded, and is a combined JTAG and serial wire debug
port that enables either a serial wire debug or a JTAG probe to be connected to the target.
Simultaneous sample and hold
Interleaved sample and hold
two DAC converters: one for each output channel
8-bit or 12-bit monotonic output
left or right data alignment in 12-bit mode
synchronized update capability
noise-wave generation
triangular-wave generation
dual DAC channel independent or simultaneous conversions
DMA capability for each channel
external triggers for conversion
input voltage reference V
Doc ID 022152 Rev 1
REF+
STM32F405xx, STM32F407xx