ATV12H075M2 Crouzet USA, ATV12H075M2 Datasheet - Page 25

• Manufacturer Part Number: ATV12H075M2
• Description: 11R1089
• Manufacturer: Crouzet USA

Specifications of ATV12H075M2

• No. Of Phases: Single
• Power Rating: 0.75kW
• Output Voltage Max: 230V
• Frequency Range: 0.5 To 400Hz
• Output Current: 4.2A
• Supply Voltage Max: 230V
• Rohs Compliant: Yes

Connections
installation
recommendations
b Grounds between the drive, motor and cable shielding must have "high frequency" equipotentiality.
b Use shielded cables with shielding connected to ground throughout 360° at both ends for the motor cable and the control-signalling cables.
Conduit or metal ducting can be used for part of the shielding length provided that there is no break in the continuity of the ground connection.
b Ensure maximum separation between the line supply cable and the motor cable.
3
2
1
Note: The HF equipotential ground connection between the drive, motor and cable shielding does not remove the need to connect the PE conductors (green-
yellow) to the appropriate terminals on each unit. If using an additional EMC input filter, it should be mounted beneath the drive and connected directly to the line
supply via an unshielded cable. Link
Use a permanent insulation monitor, such as Schneider Electric's XM200, which is compatible with non-linear loads. ATV12ppppM2 drives
have integrated EMC filters.
For use on an IT system, these filters can easily be disconnected by means of a selector switch 10
the drive.
Introduction:
page 8
Additional EMC input filters VW3A4416 to 419
Recommended connections
Braking unit VW3A7005 used with braking
resistors VW3A7701, 702, 723, 724
Single-phase power supply
Connections for ensuring conformity to EMC standards
Principle
Installation diagram
Use on an IT system (isolated or impedance grounded neutral)
ATV12pppppp
Braking unit
VW3A7 005
8
4
PB
PA
9
7
10
VW3A4416, 417
ATV12ppppF1
ATV12ppppM2
Braking
resistor
VW3A77pp
(continued)
5
6
Specifications:
page 10
3
on the drive is then established via the filter output cable.
(continued)
,
Altivar
variable speed drives
Braking unit and resistors, motor chokes,
additional EMC filters
1
2
3
4
5
6
7
8
9
10
References:
page 14
Motor chokes VW3A4551 to 554
Three-phase power supply
Metal plate to be mounted on the drive (grounded casing).
ATV12
Unshielded power supply wires or cable
Unshielded wires or cable for the output of the fault relay contacts
Shielding of cables
the drive:
-
-
the shielding.
The shielding must be clamped tightly enough to the metal surface to ensure
good contact.
For cables
The shielding must be continuous, and if intermediate terminals are used,
they must be placed in EMC shielded metal boxes.
Shielded cable for connecting the motor
Shielded cable for connecting the control-signalling cables. For applications
requiring several conductors, use cables with a small cross-section (0.5 mm
Unshielded cable for connecting the braking unit
PE cable (green-yellow)
drives
Strip the cable to expose the shielding.
Attach the cable to the plate
Selector switch for disconnecting the integrated EMC filter on ATV12
pppppp drives
3
M
6
and 7, the shielding must be connected to ground at both ends.
®
12
6
VW3A4418, 419
ATV12pppppp
VW3A455p
ATV12ppppM3
and
7
Dimensions:
page 18
attached and grounded as close as possible to
1
by tightening the clamp on the stripped part of
which can be accessed without removing
Functions:
page 26
ppppM2
2
)
23
10
1
2
3
4
5
6
7
8
9