X24C04P Xicor, X24C04P Datasheet
X24C04P
Available stocks
Related parts for X24C04P
X24C04P Summary of contents
Page 1
... The X24C04 features a serial interface and software protocol allowing operation on a simple two wire bus. The X24C04 is fabricated with Xicor’s advanced CMOS Textured Poly Floating Gate Technology. The X24C04 utilizes Xicor’s proprietary DirectWrite™ cell providing a minimum endurance of 100,000 cycles and a minimum data retention of 100 years ...
Page 2
X24C04 PIN DESCRIPTIONS Serial Clock (SCL) The SCL input is used to clock all data into and out of the device. Serial Data (SDA) SDA is a bidirectional pin used to transfer data into and out of the device. It ...
Page 3
X24C04 DEVICE OPERATION The X24C04 supports a bidirectional bus oriented pro- tocol. The protocol defines any device that sends data onto the bus as a transmitter, and the receiving device as the receiver. The device controlling the transfer is a ...
Page 4
X24C04 Stop Condition All communications must be terminated by a stop condi- tion, which is a LOW to HIGH transition of SDA when SCL is HIGH. The stop condition is also used by the X24C04 to place the device in ...
Page 5
X24C04 DEVICE ADDRESSING Following a start condition the master must output the address of the slave it is accessing. The most significant four bits of the slave are the device type identifier (see Figure 4). For the X24C04 this is ...
Page 6
X24C04 Page Write The X24C04 is capable of a sixteen byte page write operation initiated in the same manner as the byte write operation, but instead of terminating the write cycle after the first data word is transferred, ...
Page 7
X24C04 Current Address Read Internally the X24C04 contains an address counter that maintains the address of the last word accessed, incremented by one. Therefore, if the last access (either a read or write) was to address n, the next read ...
Page 8
X24C04 Sequential Read Sequential Read can be initiated as either a current address read or random access read. The first word is transmitted as with the other modes, however, the master now responds with an acknowledge, indicating it requires additional ...
Page 9
X24C04 ABSOLUTE MAXIMUM RATINGS* Temperature Under Bias .................. – +135 C Storage Temperature ....................... – +150 C Voltage on any Pin with Respect to V ............................ –1.0V to +7.0V SS D.C. Output Current ............................................ 5 mA ...
Page 10
X24C04 A.C. CONDITIONS OF TEST Input Pulse Levels V CC Input Rise and Fall Times Input and Output Timing Levels A.C. CHARACTERISTICS (Over recommended operating conditions unless otherwise specified) Read & Write Cycle Limits Symbol Parameter f SCL Clock Frequency ...
Page 11
X24C04 Write Cycle Limits Symbol Parameter (6) t Write Cycle Time WR The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle. During the write cycle, ...
Page 12
X24C04 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX PIN 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7 0.050 (1.27) 0.010 (0.25 0.020 (0.50) 0 – 8 0.027 (0.683) ...
Page 13
X24C04 PACKAGING INFORMATION 14-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX PIN 1 (4X) 7 0.050 (1.27) 0 – 8 NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 0.150 (3.80) 0.158 (4.00) 0.014 (0.35) 0.019 ...
Page 14
... LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. ...
Page 15
X24C04 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P PIN 1 INDEX HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) MAX. TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING ...
Page 16
X24C04 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX (4X) 7 0.050 (1.27) 0.010 (0.25) 0.020 (0.50) 0 – 8 0.016 (0.410) 0.037 (0.937) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESIS IN MILLIMETERS) 0.150 (3.80) 0.158 ...
Page 17
X24C04 14-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX PIN 1 0.014 (0.35) 0.020 (0.51) 0.336 (8.55) 0.345 (8.75) (4X) 7 0.050 (1.27) 0.010 (0.25 0.020 (0.50) 0 – 8 0.016 (0.41) 0.037 (0.937) ...
Page 18
X24C04 8-LEAD HERMETIC DUAL IN-LINE PACKAGE TYPE D SEATING PLANE 0.150 (3.81) MIN. NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 0.405 (10.29) –– PIN 1 0.300 (7.62) REF. 0.200 (5.08) 0.125 (3.18) 0.110 (2.79) 0.090 (2.29) TYP. 0.100 ...