OP400G Analog Devices, OP400G Datasheet
OP400G
Specifications of OP400G
Available stocks
Related parts for OP400G
OP400G Summary of contents
Page 1
... Figure 1. Simplified Schematic (One of Four Amplifiers is Shown) REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use ...
Page 2
... OP400F OP400G/H Typ Max Min Typ Max 60 230 80 300 0.1 0.1 0.1 2.0 0.1 3.5 0.75 6.0 0.75 7.0 0.5 ...
Page 3
... 1000 2300 ± 12 ± 12.5 115 130 0.2 3.2 ± 12 ± 12.4 ± 11 ± 12 600 775 8 < for OP400G for OP400E/ OP400F OP400G/H Typ Max Min Typ Max 80 350 110 400 0.3 2.0 0.6 2.5 0.1 3.5 0.2 6 ...
Page 4
... OUT A 8. OUT C 2. – – +INA 10 +IN B 12. +IND 6. –IN B 13. – OUT B 14. OUT D OP400GBC Limit Unit mA Max 230 2 nA Max 6 nA Max 3000 1500 V/mV Min ± Min 115 dB Min mV/V Max 3.2 ± ...
Page 5
TPC 1. Warm-Up Drift TPC 4. Input Offset Current vs. Temperature TPC 7. Noise Voltage Density vs. Frequency REV. A Typical Performance Characteristics–OP400 TPC 2. Input Offset Voltage vs. Temperature TPC 5. Input Bias Current vs. Common-Mode Voltage TPC 8. ...
Page 6
OP400 TPC 10. Total Supply Current vs. Supply Voltage TPC 13. Power Supply Rejection vs. Temperature TPC 16. Closed-Loop Gain vs. Frequency TPC 11. Total Supply Current vs. Temperature TPC 14. Open-Loop Gain vs. Temperature TPC 17. Maximum Output Swing ...
Page 7
TPC 19. Overshoot vs. Capacitive Load TPC 22. Large-Signal Transient Response REV. A TPC 20. Short Circuit vs. Time TPC 23. Small-Signal Transient Response Figure 2. Noise Test Schematic –7– OP400 TPC 21. Channel Separation vs. Frequency TPC 24. Small-Signal ...
Page 8
OP400 Figure 3. Burn-In Circuit APPLICATIONS INFORMATION The OP400 is inherently stable at all gains and is capable of driving large capacitive loads without oscillating. Nonetheless, good supply decoupling is highly recommended. Proper supply decoupling reduces problems caused by supply ...
Page 9
BIPOLAR CURRENT TRANSMITTER In the circuit of Figure 5, which is an extension of the standard three op amp instrumentation amplifier, the output current is proportional to the differential input voltage. Maximum output current is ± with voltage ...
Page 10
OP400 MULTIPLE OUTPUT TRACKING VOLTAGE REFERENCE Figure 7 shows a circuit that provides outputs 7 and 2.5 V for use as a system voltage reference. Maximum output current from each reference ...
Page 11
Hermetic DIP Package (Y-Suffix) 0.005 (0.13) MIN 0.098 (2.49) MAX 14 8 0.310 (7.87) PIN 1 0.220 (5.59 0.100 (2.54) BSC 0.785 (19.94) MAX 0.060 (1.52) 0.015 (0.38) 0.200 (5.08) 0.150 MAX (3.81) 0.200 (5.08) MIN 0.125 ...
Page 12
–12– ...