MC68HC705C8ACS

Manufacturer Part NumberMC68HC705C8ACS
ManufacturerFreescale Semiconductor, Inc
MC68HC705C8ACS datasheet
 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Page 111
112
Page 112
113
Page 113
114
Page 114
115
Page 115
116
Page 116
117
Page 117
118
Page 118
119
Page 119
120
Page 120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
Page 112/222

Download datasheet (3Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
EPROM/OTPROM (PROM)
9.4.2 Verify PROM Contents
The verify PROM contents routine is normally run automatically after the
PROM is programmed. Direct entry to this routine causes the PROM
contents of the MCU to be compared to the contents of the external
memory locations of the EPROM at the same addresses.
To invoke the verify PROM contents routine of the MCU, take these
steps:
1. Set switch 1 in the ON position (restores V
2. Connect V
3. Set switches S3, S4, and S6 in the OFF position.
4. Set S5 in the ON position.
5. Set switch 2 in the OUT position (routine is activated).
6. Set switch 2 in the RESET position.
At this point, if another routine is to be performed on the MCU being
programmed, the user can set switches S3, S4, S5, and S6 to the
positions necessary to select the next routine and move switch S2 to the
OUT position to start the routine. If no other routine is to be performed,
remove V
socket.
9.4.3 Secure PROM
The secure PROM routines are used after the PROM is successfully
programmed and verified. Only the SEC bit of the option register
($1FDF) is programmed, but V
programmed, PROM is secure and can be neither verified nor dumped.
Technical Data
112
to V
.
PP
DD
The red LED is not illuminated during this routine, since no
programming takes place. If verification fails, the routine halts with
the failing address in the external memory bus. When the green
LED is illuminated, verification is completed successfully and the
routine is finished.
from the board and remove the MCU from the programming
DD
is necessary. Once this bit is
PP
EPROM/OTPROM (PROM)
For More Information On This Product,
Go to: www.freescale.com
).
DD
MC68HC705C8A — Rev. 3