MC68HC705C8ACS

Manufacturer Part NumberMC68HC705C8ACS
ManufacturerFreescale Semiconductor, Inc
MC68HC705C8ACS datasheet
 
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
Page 111
112
Page 112
113
Page 113
114
Page 114
115
Page 115
116
Page 116
117
Page 117
118
Page 118
119
Page 119
120
Page 120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
Page 113/222

Download datasheet (3Mb)Embed
PrevNext
Freescale Semiconductor, Inc.
9.4.4 Secure PROM and Verify
This routine is used after the PROM is programmed successfully to
verify the contents of the MCU PROM against the contents of the
EPROM and then to secure the PROM. To accomplish this routine, take
these steps:
1. Set switch 1 in the ON position (restores V
2. Restore V
3. Set switches S4 and S6 in the OFF position.
4. Set switches S3 and S5 in the ON position.
5. Set switch 2 in the OUT position (routine is activated).
6. Set switch 2 in the RESET position when the routine is completed.
No LED is illuminated during this routine. Further, the end of the routine
does not mean that the SEC bit was verified. To ensure that security is
properly enabled, attempt to perform another verify routine. If the green
LED does not light, the PROM has been secured properly.
9.4.5 Secure PROM and Dump
This routine is used after the PROM is successfully programmed to
dump the contents of the MCU PROM through the SCI (binary upload)
and then to secure the PROM. To accomplish this routine, take these
steps:
1. Set switch 1 in the ON position (restores V
2. Restore V
3. Set switch S6 in the OFF position.
4. Set switches S3, S4, and S5 in the ON position.
5. Set switch 2 in the OUT position (routine is activated).
6. Set switch 2 in the RESET position when the routine is completed.
MC68HC705C8A — Rev. 3
MOTOROLA
For More Information On This Product,
power to the programming board.
PP
Execution time for this routine is about one second.
power to the programming board.
PP
Execution time for this routine is about one second.
EPROM/OTPROM (PROM)
Go to: www.freescale.com
EPROM/OTPROM (PROM)
PROM Programming Routines
).
DD
).
DD
Technical Data