AD8063 Analog Devices, AD8063 Datasheet
AD8063
Specifications of AD8063
Available stocks
Related parts for AD8063
AD8063 Summary of contents
Page 1
... The AD8061, AD8062, and AD8063 offer a typical low power of 6.8 mA/amplifier, while being capable of delivering load current. The AD8063 has a power-down disable feature that reduces the supply current to 400 A. These features make the AD8063 ideal for portable and battery-powered applications where size and power is critical. – ...
Page 2
... Turn-On Time Turn-Off Time DISABLE Voltage—Off DISABLE Voltage—On POWER SUPPLY Operating Range Quiescent Current per Amplifier Supply Current when Disabled (AD8063 Only) Power Supply Rejection Ratio Specifications subject to change without notice. Conditions 0 –1, + 0.2 V p-p ...
Page 3
... Turn-Off Time DISABLE Voltage—Off DISABLE Voltage—On POWER SUPPLY Operating Range Quiescent Current per Amplifier Supply Current when Disabled (AD8063 Only) Power Supply Rejection Ratio Specifications subject to change without notice. REV unless otherwise noted) ...
Page 4
... Turn-On Time Turn-Off Time DISABLE Voltage—Off DISABLE Voltage—On POWER SUPPLY Operating Range Quiescent Current per Amplifier Supply Current when Disabled (AD8063 Only) Power Supply Rejection Ratio Specifications subject to change without notice. Conditions 0 –1, + 0.2 V p-p ...
Page 5
... ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the AD8061/AD8062/AD8063 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality ...
Page 6
... AD8061/AD8062/AD8063 1.2 1.0 +V OUT +V @ +25 C OUT 0 –40 C OUT 0.6 –V @ –40 C OUT 0.4 0.2 –V @ +25 C OUT LOAD CURRENT – mA Figure 3. Output Saturation Voltage vs. Load Current SINGLE POWER SUPPLY – Voltage Figure 4. I vs. V SUPPLY ...
Page 7
... Figure 14. Harmonic Distortion vs. Output Signal DC Bias –7– AD8061/AD8062/AD8063 2ND @ 1MHz 3RD @ 10MHz 3RD @ 1MHz 2ND @ 10MHz 0.5 1.0 1.5 2.0 2.5 3.0 INPUT SIGNAL BIAS – Volts 604 ...
Page 8
... AD8061/AD8062/AD8063 – – 2ND @ 10MHz –60 –70 2ND @ 2MHz –80 2ND @ 500kHz –90 3RD @ 2MHz –100 3RD @ 500kHz –110 1.0 1.5 2.0 2.5 3.0 RTO OUTPUT – Volts pk-pk Figure 15. Harmonic Distortion vs. Output Signal Amplitude – – p-p ...
Page 9
... Figure 25. Output Overload Recovery, Input Step = – –20 –30 –40 –50 –60 –70 –80 –90 –100 10M 100k 1M 0.01 –9– AD8061/AD8062/AD8063 OUT 500mV/DIV 100 120 140 160 TIME – ...
Page 10
... AD8061/AD8062/AD8063 0.2V p – +5V S –20 –PSRR –30 –40 –50 +PSRR –60 –70 –80 –90 –100 0.01 0.1 1 FREQUENCY – MHz Figure 27. PSRR vs. Frequency Delta – –30 +2.5V –40 OUT IN – –2.5V –60 –70 INPUT = SIDE 2 –90 –80 –100 –110 –120 ...
Page 11
... L 500mV/DIV 0 2.6V 2.5V 2. 20mV/DIV 2 2.5 0 OUT – 0. s/DIV –11– AD8061/AD8062/AD8063 p TIME – ns Figure 36 Step Response 100mV IN 10 ...
Page 12
... TIME – ns Figure 40 Step Response CIRCUIT DESCRIPTION The AD8061/AD8062/AD8063 family are very high-speed volt- age feedback op amps. The high slew rate input stage is a true single-supply topology, capable of sensing signals at or below the minus supply rail. The rail-to-rail output stage can pull within either supply rail when driving light loads and within 0 ...
Page 13
... AD8061/AD8062/AD8063 VOLTAGE STEP FROM 2.4V TO 3.4V VOLTAGE STEP FROM 2.4V TO 3.6V VOLTAGE STEP FROM 2.4V TO 3.8V, 4 AND 5V 100 ...
Page 14
... Figure 48. Disable Circuit of the AD8063 Figure 30 shows AD8063 supply current versus DISABLE volt- age. Figure 31 plots the output seen when the AD8063 input is driven with a 10 MHz sine wave, and the DISABLE is toggled from illustrating the part’s turn on and turn off time. ...
Page 15
... RGB system. Figure 51 shows a circuit that performs this function. Multiplexer The AD8063 has a disable pin that can be used to power-down the amplifier to save power, or can be used to create a mux circuit. If two (or more) AD8063 outputs are connected together and only one is enabled, then only the signal of the enabled amplifi ...
Page 16
... OUTPUT SELECT 1V 2V Figure 53. AD8063 Mux Output 8-Lead SOIC (R-8) 0.1968 (5.00) 0.1890 (4.80 0.2440 (6.20) 0.2284 (5.80 0.0196 (0.50) 0.0500 (1.27) BSC 0.0099 (0.25) 0.102 (2.59) 0.094 (2.39) 8 0.0192 (0.49) 0 0.0500 (1.27) 0.0098 (0.25) SEATING 0 ...