AD811ANZ Analog Devices Inc, AD811ANZ Datasheet - Page 17

• Manufacturer Part Number: AD811ANZ
• Description: IC OPAMP VIDEO HP 8-DIP
• Manufacturer: Analog Devices Inc

Specifications of AD811ANZ

• Slew Rate: 2500 V/µs
• Applications: Current Feedback
• Number Of Circuits: 1
• -3db Bandwidth: 140MHz
• Current - Supply: 16.5mA
• Current - Output / Channel: 100mA
• Voltage - Supply, Single/dual (±): ±4.5 V ~ 18 V
• Mounting Type: Through Hole
• Package / Case: 8-DIP (0.300", 7.62mm)
• Gain Bandwidth: 140MHz
• Supply Voltage Range: ± 4.5V To ± 18V
• No. Of Amplifiers: 1
• Output Current: 100mA
• Amplifier Output: Single Ended
• Amplifier Type: Video
• Bandwidth: 140 MHz
• Common Mode Rejection Ratio: 60
• Current, Input Bias: 2 μA
• Current, Output: 100 mA
• Harmonic Distortion: -74 dBc
• Impedance, Thermal: 90 °C/W
• Package Type: PDIP-8
• Resistance, Input: 1.5 Megohms (+Input), 14 Ohms (-Input)
• Temperature, Operating, Range: -40 to +85 °C
• Voltage, Input: ±3 V (Common-Mode)
• Voltage, Noise: 1.9 nV/sqrt Hz
• Voltage, Offset: 0.5 mV
• Voltage, Output, High: +12 V
• Voltage, Output, Low: -12 V
• Voltage, Supply: ±15 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

To generate the 1 V dc needed for the 1−G term, an AD589
reference supplies 1.225 V ± 25 mV to a voltage divider consist-
ing of resistors R2 through R4. Potentiometer R3 should be
adjusted to provide exactly 1 V at the X1 input.
In this case, an arrangement is shown using dual supplies of
±5 V for both the AD834 and the AD811. Also, the overall gain
is arranged to be unity at the load when it is driven from a
reverse-terminated 75 Ω line. This means that the dual VCA has
to operate at a maximum gain of +2, rather than +4 as in the
VCA circuit of Figure 47. However, this cannot be achieved by
lowering the feedback resistor because below a critical value
(not much less than 500 Ω) the AD811’s peaking may be
unacceptable. This is because the dominant pole in the open-
loop ac response of a current feedback amplifier is controlled
this feedback resistor. It would be possible to operate at a gain of
×4 and then attenuate the signal at the output. Instead, the
signals have been attenuated by 6 dB at the input to the AD811;
this is the function of R8 through
Figure 49 is a plot of the ac response of the feedback keyer when
driving a reverse-terminated 50 Ω cable. Output noise and
adjacent channel feedthrough, with either channel fully off and
the other fully on, is about −50 dB to 10 MHz. The feedthrough
R11.
Rev. E | Page 17 of 20
by
at 100 MHz is limited primarily by board layout. For V
the −3 dB bandwidth is 15 MHz when using a 137 Ω resistor for
R14 and 70 MHz with R14 = 49.9 Ω. For more information on
the design and operation of the VCA and video keyer circuits,
refer to the application note “Video VCAs and Keyers: Using the
AD834 and AD811” by Brunner, Clarke, and Gilbert, available
on the Analog Devices, Inc. website at www.analog.com.
–10
–20
–30
–40
–50
–60
–70
–80
–90
10
0
10k
Figure 49. A Plot of the AC Response of the Video Keyer
100k
GAIN
ADJACENT CHANNEL
FEEDTHROUGH
FREQUENCY (Hz)
1M
R14 = 137Ω
10M
R14 = 49.9Ω
100M
AD811
G
= 1 V,