TPD4103K TOSHIBA Semiconductor CORPORATION, TPD4103K Datasheet
TPD4103K
Available stocks
Related parts for TPD4103K
TPD4103K Summary of contents
Page 1
... TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC The TPD4103K brushless motor driver using high voltage PWM control fabricated by high voltage SOI process. It contains level shift high-side driver, low side driver, IGBT outputs, FRDs and protective functions for over current and under voltage protection circuits, and thermal shutdown circuit ...
Page 2
... Weekly code:(Three digits BSV V NC BSW W Toshiba trademark * Lot No. JAPAN Product No Week of manufacture(01 for first week of year, continues 53) Year of manufacture(One low-order digits of calendar year) 2 TPD4103K IS2 DIAG V GND REG 2003-08-21 23 ...
Page 3
... DIAG 19 Under- Under- Under- voltage voltage voltage protection protection protection Under- voltage High-side level protection shift driver Thermal shutdown Low-side driver Dead time COMP 0.5Vref 3 TPD4103K BSU 8 BSV 11 BSW IS2 7 IS1 21 GND 2003-08-21 ...
Page 4
... With the diagnostic output terminal of open drain, a pull-up is carried out by resistance. 19 DIAG It turns the time of unusual Control power supply pin. (15V typ GND Ground pin regulator output pin. REG 23 NC Unused pin, which is not connected to the chip internally. Pin Description 4 TPD4103K 2003-08-21 ...
Page 5
... Internal circuit diagram of HU, HV, HW, LU, LV, LW input pins V REG 5 kΩ 5 kΩ HU/HV/HW LU/LV/LW 6.5 V 6.5 V Internal circuit diagram of DIAG pin To internal circuit Internal circuit diagram of IS pin 10 kΩ 440 kΩ IS 6 internal circuit 2 kΩ 6.5 V 6.5 V DIAG 5 kΩ internal circuit TPD4103K 2003-08-21 ...
Page 6
... Timing Chart Input signal Output voltage VW 6 TPD4103K 2003-08-21 ...
Page 7
... REG −20~135 T °C jopr T 150 °C j −55~150 T °C stg Vhs 1000 (1 min) Vrms 7 TPD4103K Bottom arm DIAG phase phase phase phase OFF OFF ON OFF OFF OFF OFF OFF ON OFF OFF OFF OFF ON OFF ...
Page 8
... UVR DIAGsat DIAG = 280 0 280 0 off BB = 280 0.5 A tdead 280 0 TPD4103K Min Typ. Max Unit 50 280 400 V 13.5 15 16.5 0.1 0.5 mA 1.1 5 260 410 µA 230 370 ...
Page 9
... DIAG R 2 Under- Under- Under- voltage voltage voltage protection protection protection Under- High-side Level voltage Shift Driver protection Thermal shutdown Input control Low-side driver COMP 0.5Vref 9 TPD4103K 8 BSU 11 BSV 14 BSW IS2 7 Dead time ...
Page 10
... DIAG pin pull-up resistor = protection circuit is triggered so that the current flows continuously. If not CC power supply are not cared about either. CC power supply is blocked when the TPD4103K Remarks (Note 1) (Note 2) (Note 3) (Note 3) (Note 3) (Note 3) (Note 4) ÷ RIS (For voltage is steady ...
Page 11
... Note 2: The above safe operating areas include the over current protection operation area. voltage or the V voltage drops UVD = 9 V typ.), the high-side IGBT output shuts down. BS 1.1 0 400 0 ( TPD4103K = 0.5 V (typ.), the IGBT R UVD = 11 V typ.), all IGBT CC 400 Power supply voltage V (V) BB Figure 2 SOA 95°C 2003-08-21 ...
Page 12
... Junction temperature T 1.6 1.4 1.2 1.0 0.8 −20 140 20 Junction temperature T 8.0 I reg = 30 mA 7.5 7.0 6.5 6 (V) Control power supply voltage V 12 TPD4103K V L – T CEsat 700 500 300 mA 60 100 140 (° – 700 500 300 mA 60 100 140 (° ...
Page 13
... Junction temperature T 10 UVD V BS UVR 10.0 9.5 9.0 8.5 8.0 −20 140 20 Junction temperature T 6 4.0 2.0 0 −20 140 20 Junction temperature T 13 TPD4103K t – T OFF j 60 100 140 (° – 100 140 (° – T ｔ 100 140 (°C) ...
Page 14
... Control power supply voltage V 250 200 150 100 50 0 −20 140 20 Junction temperature T 140 14 TPD4103K I – V (OFF −20°C 25°C 135° (V) BS Wton – 700 500 300 mA 60 100 140 (° ...
Page 15
... Test Circuits IGBT Saturation Voltage FRD Forward Voltage (U-phase low side) (U-phase low side TPD4103K 2003-08-21 ...
Page 16
... V Current Dissipation CC Regulator Voltage IM 16 TPD4103K = 2003-08-21 ...
Page 17
... Output ON/OFF Delay Time (U-phase low side) IM 90% 10% 90% 17 TPD4103K 280 V 10% t OFF 2003-08- ...
Page 18
... The BSU pin voltage when output is on defines the under voltage protection recovery voltage. (U-phase low side) pin voltage when output is on defines the under voltage protection CC (U-phase high side) pin voltage TPD4103K → ...
Page 19
... Note: Sweeps the IS pin voltage to increase and monitors the U pin voltage. The IS pin voltage when output is off defines the current control operating voltage. V Current Consumption (U-phase high side) BS (U-phase high side TPD4103K → ...
Page 20
... BSD Forward Voltage (U-phase TPD4103K 2003-08-21 ...
Page 21
... IGBT + + + + high-side FRD) Turn-On/Off Loss VM Input (LU) IGBT (C-E voltage) (U-GND) Power supply current Wtoff Wton 21 TPD4103K 280 2003-08-21 ...
Page 22
... Package Dimensions Weight: 6.1 g (typ.) 22 TPD4103K 2003-08-21 ...
Page 23
... Package Dimensions Weight: 6.1 g (typ.) 23 TPD4103K 2003-08-21 ...
Page 24
... Package Dimensions Weight: 6.1 g (typ.) 24 TPD4103K 2003-08-21 ...
Page 25
... The products described in this document are subject to the foreign exchange and foreign trade laws. • TOSHIBA products should not be embedded to the downstream products which are prohibited to be produced and sold, under any law and regulations. 25 TPD4103K 030619EBA 2003-08-21 ...