AT89LP213 Atmel Corporation, AT89LP213 Datasheet - Page 77

• Manufacturer Part Number: AT89LP213
• Manufacturer: Atmel Corporation

Specifications of AT89LP213

• Flash (kbytes): 2 Kbytes
• Max. Operating Frequency: 20 MHz
• Cpu: 8051-1C
• Max I/o Pins: 14
• Spi: 1
• Sram (kbytes): 0.125
• Operating Voltage (vcc): 2.4 to 5.5
• Timers: 2
• Isp: SPI/OCD
• Watchdog: Yes

24. Electrical Characteristics
24.1
24.2
T
Notes:
3538E–MICRO–11/10
Operating Temperature ................................... -40°C to +85°C
Storage Temperature ..................................... -65°C to +150°C
Voltage on Any Pin with Respect to Ground......-0.7V to +5.5V
Maximum Operating Voltage ............................................ 5.5V
DC Output Current...................................................... 15.0 mA
Symbol
V
V
V
V
V
I
I
I
V
V
RRST
C
I
A
IL
TL
LI
CC
IL
IH
OL
OH
OH1
OS
CM
IO
= -40°C to 85°C, V
Absolute Maximum Ratings*
DC Characteristics
1. Under steady state (non-transient) conditions, I
2. V
3. Minimum V
Maximum I
Maximum total I
If I
than the listed test conditions.
OH1
OL
Parameter
Input Low-voltage
Input High-voltage
Output Low-voltage
Output High-voltage (Ports 1, 3)
With Weak Pull-ups Enabled
Output High-voltage (Ports 1, 3)
With Strong Pull-ups Enabled
Logic 0 Input Current
(Quasi-Bidirectional Mode)
Logic 1 to 0 Transition Current
(Quasi-Bidirectional Mode)
Input Leakage Current
(Input-Only Mode)
Comparator Input Offset Voltage
Comparator Input Common
Mode Voltage
Reset Pull-up Resistor
Pin Capacitance
Power Supply Current
Power-down Mode
exceeds the test condition, V
levels are listed for DC operation. Under AC conditions a boost circuit provides additional source current.
OL
CC
CC
per port pin: 10 mA
for Power-down is 2V.
= 2.4V to 5.5V (unless otherwise noted)
OL
for all output pins: 15 mA
(3)
(1)
(Ports 1, 3)
OL
(2)
may exceed the related specification. Pins are not guaranteed to sink current greater
Condition
I
I
I
I
I
I
I
V
V
0 < V
V
Test Freq. = 1 MHz, T
Active Mode, 12 MHz, V
Idle Mode, 12 MHz, V
V
V
OL
OH
OH
OH
OH
OH
OH
IN
IN
CC
CC
CC
= 10 mA, T
= -80 µA, V
= -25 µA
= -10 µA
= -2 mA, V
= -500 µA, V
= -100 µA
= 0.45V
= 2V, V
= 5V
= 5V, P1.0 & P1.1 = 0V or V
= 3V, P1.0 & P1.1 = 0V or V
IN
OL
< V
must be externally limited as follows:
CC
CC
= 5V ± 10%
A
CC
CC
= 85°C
CC
= 5V ± 10%
= 5V ± 10%
*NOTICE:
= 5V ± 10%
A
CC
= 25°C
CC
= 5./3V
= 5V/3V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
CC
CC
0.7 V
0.7 V
0.9 V
0.6 V
0.6 V
Min
-0.5
2.4
2.4
50
0
CC
CC
CC
CC
CC
AT89LP213/214
V
0.3 V
CC
3/1.5
Max
-300
10/6
V
150
±10
0.5
-50
20
10
5
2
+ 0.5
CC
CC
Units
mV
mA
mA
KΩ
µA
µA
µA
pF
µA
µA
V
V
V
V
V
V
V
V
V
V
77