ATtiny167 Atmel Corporation, ATtiny167 Datasheet - Page 10

• Manufacturer Part Number: ATtiny167
• Manufacturer: Atmel Corporation

Specifications of ATtiny167

• Flash (kbytes): 16 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 3
• Input Capture Channels: 1
• Pwm Channels: 9
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Notes:
10
0x1A (0x3A)
0x0E (0x2E)
0x0D (0x2D)
0x0C (0x2C)
0x0B (0x2B)
0x0A (0x2A)
0x19 (0x39)
0x18 (0x38)
0x17 (0x37)
0x16 (0x36)
0x15 (0x35)
0x14 (0x34)
0x13 (0x33)
0x12 (0x32)
0x11 (0x31)
0x10 (0x30)
0x0F (0x2F)
0x09 (0x29)
0x08 (0x28)
0x07 (0x27)
0x06 (0x26)
0x05 (0x25)
0x04 (0x24)
0x03 (0x23)
0x02 (0x22)
0x01 (0x21)
0x00 (0x20)
Address
1. Address bits exceeding EEAMSB
2. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses
3. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these
4. Some of the status flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI
5. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O
ATtiny87/ATtiny167
should never be written.
registers, the value of single bits can be checked by using the SBIS and SBIC instructions.
instructions will only operate on the specified bit, and can therefore be used on registers containing such status flags. The
CBI and SBI instructions work with registers 0x00 to 0x1F only.
Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The ATtiny87/167 is a com-
plex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for the IN
and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only the ST/STS/STD and LD/LDS/LDD
instructions can be used.
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
PORTCR
PORTB
PORTA
Name
TIFR1
TIFR0
DDRB
DDRA
PINB
PINA
PORTB7
PORTA7
PINB7
PINA7
DDB7
DDA7
Bit 7
–
–
–
PORTB6
PORTA6
PINB6
PINA6
DDB6
DDA6
Bit 6
–
–
–
(Table 21-8 on page
PORTB5
PORTA5
PINB5
PINA5
BBMB
Bit 5
DDB5
DDA5
ICF1
–
PORTB4
PORTA4
BBMA
PINB4
PINA4
Bit 4
DDB4
DDA4
–
–
228) are don’t care.
PORTB3
PORTA3
PINB3
PINA3
DDB3
DDA3
Bit 3
–
–
–
PORTB2
PORTA2
OCF1B
PINB2
PINA2
DDB2
DDA2
Bit 2
–
–
PORTB1
PORTA1
OCF1A
OCF0A
PUDB
PINB1
PINA1
DDB1
DDA1
Bit 1
PORTB0
PORTA0
PINB0
PINA0
PUDA
DDB0
DDA0
Bit 0
TOV1
TOV0
8265BS–AVR–09/10
page 139
page 105
page 75
page 86
page 86
page 86
page 86
page 86
page 86
Page