SAM3N4A Atmel Corporation, SAM3N4A Datasheet - Page 393

• Manufacturer Part Number: SAM3N4A
• Manufacturer: Atmel Corporation

Specifications of SAM3N4A

• Flash (kbytes): 256 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 48 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 79
• Ext Interrupts: 79
• Quadrature Decoder Channels: 2
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 2
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 24
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 6
• Output Compare Channels: 6
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 26-6. Input Debouncing Filter Timing
26.5.10
11011A–ATARM–04-Oct-10
11011A–ATARM–04-Oct-10
Divided Slow Clock
if PIO_IFSR = 0
if PIO_IFSR = 1
PIO_PDSR
PIO_PDSR
Pin Level
Input Edge/Level Interrupt
up to 2 cycles Tmck
The PIO Controller can be programmed to generate an interrupt when it detects an edge or a
level on an I/O line. The Input Edge/Level Interrupt is controlled by writing PIO_IER (Interrupt
Enable Register) and PIO_IDR (Interrupt Disable Register), which respectively enable and dis-
able the input change interrupt by setting and clearing the corresponding bit in PIO_IMR
(Interrupt Mask Register). As Input change detection is possible only by comparing two succes-
sive samplings of the input of the I/O line, the PIO Controller clock must be enabled. The Input
Change Interrupt is available, regardless of the configuration of the I/O line, i.e. configured as an
input only, controlled by the PIO Controller or assigned to a peripheral function.
By default, the interrupt can be generated at any time an edge is detected on the input.
Some additional Interrupt modes can be enabled/disabled by writing in the PIO_AIMER (Addi-
tional Interrupt Modes Enable Register) and PIO_AIMDR (Additional Interrupt Modes Disable
Register). The current state of this selection can be read through the PIO_AIMMR (Additional
Interrupt Modes Mask Register)
These Additional Modes are:
In order to select an Additional Interrupt Mode:
• Rising Edge Detection
• Falling Edge Detection
• Low Level Detection
• High Level Detection
• The type of event detection (Edge or Level) must be selected by writing in the set of registers;
• The Polarity of the event detection (Rising/Falling Edge or High/Low Level) must be selected
PIO_ESR (Edge Select Register) and PIO_LSR (Level Select Register) which enable
respectively, the Edge and Level Detection. The current status of this selection is accessible
through the PIO_ELSR (Edge/Level Status Register).
by writing in the set of registers; PIO_FELLSR (Falling Edge /Low Level Select Register) and
PIO_REHLSR (Rising Edge/High Level Select Register) which allow to select Falling or
Rising Edge (if Edge is selected in the PIO_ELSR) Edge or High or Low Level Detection (if
up to 2 cycles Tmck
PIO_IFCSR = 1
up to 1.5 cycles Tdiv_slclk
1 cycle Tdiv_slclk
up to 2 cycles Tmck
up to 1.5 cycles Tdiv_slclk
1 cycle Tdiv_slclk
up to 2 cycles Tmck
SAM3N
SAM3N
393
393