AD7323 Analog Devices, AD7323 Datasheet - Page 19

• Manufacturer Part Number: AD7323
• Description: 500 kSPS, 4-Channel, Software Selectable True bipolar Input, 12-Bit Plus Sign A/D Converter
• Manufacturer: Analog Devices

Specifications of AD7323

• Resolution (bits): 13bit
• # Chan: 4
• Sample Rate: 500kSPS
• Interface: Ser,SPI
• Analog Input Type: Diff-Uni,SE-Uni
• Ain Range: Bip 10V,Bip 2.5V,Bip 5.0V,Uni 10V
• Adc Architecture: SAR
• Pkg Type: SOP

TYPICAL CONNECTION DIAGRAM
Figure 32 shows a typical connection diagram for the AD7323.
In this configuration, the AGND pin is connected to the analog
ground plane of the system, and the DGND pin is connected to
the digital ground plane of the system. The analog inputs on the
AD7323 can be configured to operate in single-ended, true
differential, or pseudo differential mode. The AD7323 can operate
with either an internal or external reference. In Figure 32, the
AD7323 is configured to operate with the internal 2.5 V reference.
A 680 nF decoupling capacitor is required when operating with
the internal reference.
The V
5 V supply voltage. V
high voltage analog input structures. The voltage on these pins
must be equal to or greater than the highest analog input range
selected on the analog input channels (see Table 6). The V
pin is connected to the supply voltage of the microprocessor.
The voltage applied to the V
the serial interface. V
ANALOG INPUT
Single-Ended Inputs
The AD7323 has a total of four analog inputs when operating
the AD7323 in single-ended mode. Each analog input can be
independently programmed to one of the four analog input
ranges. In applications where the signal source is high
impedance, it is recommended to buffer the signal before
applying it to the ADC analog inputs. Figure 33 shows the
configuration of the AD7323 in single-ended mode.
+15V
–15V
ANALOG INPUTS
±10V, ±5V, ±2.5V
0V TO +10V
CC
680nF
pin can be connected to either a 3 V supply voltage or a
0.1µF
0.1µF
+
+
Figure 32. Typical Connection Diagram
10µF
10µF
V
V
V
V
REFIN/OUT
IN
IN
IN
IN
0
1
2
3
V
DD
DD
DRIVE
V
1
AD7323
SS
1
MINIMUM V
DEPEND ON THE HIGHEST ANALOG INPUT
RANGE SELECTED.
1
and V
can be set to 3 V or 5 V.
AGND
DRIVE
V
CC
V
SS
DGND
DOUT
SCLK
DRIVE
DD
DIN
10µF
are the dual supplies for the
CS
input controls the voltage of
AND V
10µF
+
SS
0.1µF
SUPPLY VOLTAGES
+
0.1µF
INTERFACE
SERIAL
+3V SUPPLY
V
CC
µC/µP
+ 2.7V TO 5.25V
DRIVE
Rev. A | Page 19 of 36
True Differential Mode
The AD7323 can have a total of two true differential analog
input pairs. Differential signals have some benefits over single-
ended signals, including better noise immunity based on the
device’s common-mode rejection and improvements in distor-
tion performance. Figure 34 defines the configuration of the
true differential analog inputs of the AD7323.
The amplitude of the differential signal is the difference
between the signals applied to the V
each differential pair (V
be simultaneously driven by two signals, each of amplitude
±4 × V
out of phase. Assuming the ±4 × V
the differential signal is −20 V to +20 V p-p (2 × 4 × V
regardless of the common mode.
The common mode is the average of the two signals
and is therefore the voltage on which the two input signals are
centered.
This voltage is set up externally, and its range varies with
reference voltage. As the reference voltage increases, the
common-mode range decreases. When driving the differential
inputs with an amplifier, the actual common-mode range is
determined by the amplifier’s output swing. If the differential
inputs are not driven from an amplifier, the common-mode
range is determined by the supply voltage on the V
and the V
(V
AGND
REF
Figure 33. Single-Ended Mode Typical Connection Diagram
IN
NOTES
1. V
1
ADDITIONAL PINS OMITTED FOR CLARITY.
+ + V
SS
(depending on the input range selected) that are 180°
IN
+ CAN BE V
supply pin.
IN
−)/2
Figure 34. True Differential Inputs
IN
0 OR V
1
ADDITIONAL PINS OMITTED FOR CLARITY.
IN
+ − V
V+
V–
IN
2, AND V
V
V
IN
IN
IN
−). V
+
–
AD7323
REF
IN
IN
– CAN BE V
+ and V
mode, the amplitude of
IN
V
+ and V
IN
x
AD7323
1
IN
IN
1 OR V
V
− inputs in
V
IN
DD
SS
1
− should
DD
V
AD7323
5V
IN
CC
3.
supply pin
REF
),