DAC8426 Analog Devices, DAC8426 Datasheet
DAC8426
Specifications of DAC8426
Available stocks
Related parts for DAC8426
DAC8426 Summary of contents
Page 1
... PMI’s advanced oxide-based, silicon-gate, CMOS process al- lows the DAC8426’s analog and digital circuitry to be manufac- tured on the same chip. This, coupled with PMI’s highly stable thin-film R-2R resistor ladder, aids in matching and tempera- ture tracking between DACs ...
Page 2
... Input Capacitance POWER SUPPLIES 4 Positive Supply Current 4 Negative Supply Current 5 Power Dissipation Power Supply Sensitivity ELECTRICAL CHARACTERISTICS DAC8426AR/BR – +85 C applies for DAC8426ER/EP/FR/FP/FS, unless otherwise noted. A Parameter DAC OUTPUT 3 Output Current (Source) 3 Output Current (Sink) Minimum Load Resistance 3 DYNAMIC PERFORMANCE ...
Page 3
... DAC8426ER 1 LSB DAC8426EP 1 LSB 2 DAC8426BR 2 LSB DAC8426FR 2 LSB DAC8426FP 2 LSB 3 DAC8426FS 2 LSB NOTES 1 Burn-in is available on commercial and industrial temperature range parts in cerdip, plastic DIP, and TO-can packages. 2 For devices processed in total compliance to MIL-STD-883, add /883 after part number. Consult factory for 883 data sheet. ...
Page 4
... ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the DAC8426 features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality ...
Page 5
... Channel-to-Channel Matching (DACs Superimposed) Long Term Drift Accelerated by Burn-In Power Supply Current vs. Temperature REV. C Typical Performance Characteristics–DAC8426 Relative Accuracy vs. Code –55 C, +25 C, +125 C A (All Superimposed) V Noise Density vs. Frequency OUT PSRR vs. Frequency –5– Zero Code Error vs. Temperature ...
Page 6
... DAC8426–Typical Performance Characteristics V OUT Error from 10.000 V REF vs. Temperature V OUT Line Regulation vs. Temperature REF Output Impedance (V OUT) REF vs. Frequency V REF –6– V OUT Load Regulation REF vs. Temperature OUT Start Up REV. C ...
Page 7
... DACs being up- dated specified in nano-Volt-seconds (nVs). CIRCUIT DESCRIPTION The DAC8426 is a complete quad 8-bit D/A converter. It con- tains an internal bandgap reference, four voltage switched R-2R ladder DACs, four DAC latches, four output buffer amplifiers, and an address decoder. All four DACs share the internal ten volt reference and analog ground(AGND) ...
Page 8
... Settling Time Response (Positive Transition) Figure 3. Dynamic Response four output buffer amplifiers are connected to V the DAC8426 from dual supplies (V improves negative going output settling time near zero volts. When operating single supply (V output sink current decreases as the output approaches zero voltage ...
Page 9
... These tolerances provide the worst case analysis including tem- perature changes. REV. C One additional characteristic guaranteed is a DNL of 1 LSB on all grades. The DAC8426 is therefore guaranteed to be mon- is equal to the otonic. In the situation where a continuously positive 1 LSB OUT digital increment is applied, the output voltage will always in- crease in value, never decrease ...
Page 10
... DAC8426 ESD input protection diodes will forward bias if the applied input logic is at logic “1”. No damage will result to the input since the DAC8426 is designed to withstand mo- mentary currents 130 mA. This situation will likely exist for any DAC or ADC operating from a separate analog supply. 4. ESD input protection— ...
Page 11
... MICROPROCESSOR INTERFACING The DAC8426 easily interfaces to most 8- and 16-bit wide data- bus systems. Serial and 4-bit busses can also be accommodated with additional latches and control circuitry. Interfacing can be accomplished with databus transfers running with 50 ns write pulse widths. Examples of various microprocessor interface circuits are pro- vided in Figures 8 through 12 ...
Page 12
... DAC8426 0.200 (5.08) 0.200 (5.08) 0.125 (3.18) 0.210 (5.33) 0.160 (4.06) 0.115 (2.93) 0.0118 (0.30) 0.0040 (0.10) OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 20-Pin Cerdip (Q-20) 0.005 (0.13) MIN 0.098 (2.49) MAX 20 11 0.310 (7.87) 0.220 (5.59 PIN 1 1.060 (26.92) MAX 0.060 (1.52) 0.015 (0.38) MAX 0.150 (3.81) MIN 0.023 (0.58) 0.100 0.070 (1.78) SEATING (2.54) PLANE 0.014 (0.36) 0.030 (0.76) BSC ...