AD8566 Analog Devices, AD8566 Datasheet - Page 10

• Manufacturer Part Number: AD8566
• Description: 16 V Rail-to-Rail Operational Amplifier (Dual)
• Manufacturer: Analog Devices

Specifications of AD8566

• Vcc-vee: 4.5V to 16V
• Isy Per Amplifier: 850µA
• Packages: SOIC,SOP
• -3db Bandwidth: 5MHz
• Slew Rate: 6V/µs
• Vos: 2mV
• Ib: 600nA
• # Opamps Per Pkg: 2
• Input Noise (nv/rthz): 25nV/rtHz

AD8565/AD8566/AD8567
This input current is not inherently damaging to the device as
long as it is limited to 5 mA or less. If a condition exists using
the AD8565/AD8566/AD8567 where the input exceeds the
supply more than 0.6 V, an external series resistor should be
added. The size of the resistor can be calculated by using the
maximum over-voltage divided by 5 mA. This resistance should
be placed in series with either input exposed to an overvoltage.
OUTPUT PHASE REVERSAL
The AD8565/AD8566/AD8567 are immune to phase reversal.
Although device output does not change phase, large currents
due to input overvoltage could damage the device. In applica-
tions where the possibility of an input voltage exceeding the
supply voltage exists, overvoltage protection should be used as
described in the Input Overvoltage Protection section.
POWER DISSIPATION
The maximum allowable internal junction temperature of
150°C limits the maximum power dissipation of AD8565/
AD8566/AD8567 devices. As the ambient temperature
increases, the maximum power dissipated by AD8565/AD8566/
AD8567 devices must decrease linearly to maintain maximum
junction temperature. If this maximum junction temperature is
exceeded momentarily, the device still operates properly once
the junction temperature is reduced below 150°C. If the
maximum junction temperature is exceeded for an extended
period, overheating could lead to permanent damage of the
device.
The maximum safe junction temperature, T
the following formula, the maximum power that an AD8565/
AD8566/AD8567 device can safely dissipate as a function of
temperature can be obtained:
where:
P
T
junction temperature (150°C).
T
θ
junction-to-ambient.
JA
DISS
JMAX
A
is the ambient temperature of the circuit.
is the AD8565/AD8566/AD8567 package thermal resistance,
P
is the AD8565/AD8566/AD8567 power dissipation.
is the AD8565/AD8566/AD8567 maximum allowable
DISS
= T
JMAX
− T
A
/θ
JA
JMAX
, is 150°C. Using
Rev. G | Page 10 of 16
The power dissipated by the device can be calculated as
where:
V
V
I
Figure 30 shows the maximum power dissipation vs. temper-
ature. To achieve proper operation, use the previous equation to
calculate P
use Figure 30.
THERMAL PAD—AD8567
The AD8567 LFCSP comes with a thermal pad that is attached
to the substrate. This substrate is connected to the most positive
supply, that is, Pin 3 in the LFCSP package and Pin 4 in the
TSSOP package. To be electrically safe, the thermal pad should
be soldered to an area on the board that is electrically isolated
or connected to V
adversely affects the performance of the part.
Soldering down this thermal pad dramatically improves the
heat dissipation of the package. It is necessary to attach vias that
connect the soldered thermal pad to another layer on the board.
This provides an avenue to dissipate the heat away from the
part. Without vias, the heat is isolated directly under the part.
LOAD
S
OUT
Figure 30. Maximum Power Dissipation vs. Temperature for 5-Lead SC70,
is the supply voltage.
P
is the output voltage.
is the output load current.
1.25
1.00
0.75
0.50
0.25
DISS
8-Lead MSOP, 14-Lead TSSOP, and 16-Lead LFCSP Packages
0
–35
= (V
DISS
S
for a specific package at any given temperature or
14-LEAD TSSOP
− V
16-LEAD LFCSP
8-LEAD MSOP
5-LEAD SC70
–15
DD
OUT
. Attaching the thermal pad to ground
) × I
AMBIENT TEMPERATURE (°C)
5
LOAD
25
45
65
85