AD704 Analog Devices, AD704 Datasheet - Page 5

no-image

AD704

Manufacturer Part Number
AD704
Description
Picoampere Input Current Quad Bipolar Op Amp
Manufacturer
Analog Devices
Datasheet

Specifications of AD704

Vcc-vee
4V to 36V
Isy Per Amplifier
600µA
Packages
DIP,LCC,SOIC
-3db Bandwidth
800kHz
Slew Rate
150mV/µs
Vos
30µV
Ib
100pA
# Opamps Per Pkg
4
Input Noise (nv/rthz)
15nV/rtHz

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD704A
Manufacturer:
Freescale
Quantity:
44
Part Number:
AD704AQ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD704AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD704AR
Quantity:
25
Part Number:
AD704AR-16
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD704ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD704ARZ-16
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD704JR-16-REEL
Manufacturer:
AD
Quantity:
79
Part Number:
AD704JRZ-16-REEL
Manufacturer:
PHILIPS
Quantity:
212
Part Number:
AD704SE/883B
Manufacturer:
AD
Quantity:
1 400
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter
Supply Voltage
Internal Power Dissipation (25°C)
Input Voltage
Differential Input Voltage
Output Short-Circuit Duration (Single Input)
Storage Temperature Range
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
1
2
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
INPUT SIGNAL
NOTES
1. ALL FOUR AMPLIFIERS ARE CONNECTED AS SHOWN.
1
THE SIGNAL INPUT (SUCH THAT THE AMPLIFIER’S OUTPUT IS AT MAXIMUM
Specification is for the device in free air:
The input pins of this amplifier are protected by back-to-back diodes. If the
differential voltage exceeds ±0.7 volts, external series protection resistors
should be added to limit the input current to less than 25 mA.
AMPLITUDE WITHOUT CLIPPING OR SLEW LIMITING) IS APPLIED TO ONE
AMPLIFIER AT A TIME. THE OUTPUTS OF THE OTHER THREE AMPLIFIERS ARE
THEN MEASURED FOR CROSSTALK.
AD704J
AD704A
14-lead plastic package: θ
16-lead SOIC package: θ
20-terminal LCC package: θ
1kΩ
1
1kΩ
AD704
Figure 5. Crosstalk Test Circuit
1/4
9kΩ
JA
JA
= 100°C/W.
2
JA
= 150°C/W.
= 150°C/W.
2.5kΩ
OUTPUT
1
COM
+V
–V
S
S
0.1µF
0.1µF
Rating
 ±18 V
 ±V
 ±0.7 V
Indefinite
−65°C to +125°C
0°C to 70°C
−40°C to +85°C
300°C
1µF
1µF
S
AD704
PIN 4
AD704
PIN 11
Rev. E | Page 5 of 16
ESD CAUTION
–100
–120
–140
–160
–80
10
Figure 6. Crosstalk vs. Frequency
100
FREQUENCY (Hz)
1k
10k
AMP4
AMP2
AMP3
AD704
100k

Related parts for AD704