MAX13326GUI/V+T Maxim Integrated Products, MAX13326GUI/V+T Datasheet
MAX13326GUI/V+T
Specifications of MAX13326GUI/V+T
Related parts for MAX13326GUI/V+T
MAX13326GUI/V+T Summary of contents
Page 1
... MAX13325 MAX13326 *OPTIONAL : NEEDED FOR AUTOMOTIVE LOAD DUMP PROTECTION ONLY **USE D2 WHEN CHARGE PUMP IS OFF AND EXTERNAL SUPPLY IS PROVIDED TO C HOLD _______________________________________________________________ Maxim Integrated Products 1 For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 2 ...
Page 2
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic ABSOLUTE MAXIMUM RATINGS V to PGND ........................................................-0.3V to +28V DD CHOLD .................................................................-0.3V to +28V V to GND ...............................................................-0.3V to +6V L GND, PGND ........................................................-0.3V to +0.3V OUT_ to ...
Page 3
Dual Automotive, Audio Line Drivers ELECTRICAL CHARACTERISTICS (continued 14.4V 5V load impedance from OUT_+ to OUT_ unless otherwise noted.) (Note 2) PARAMETER SYMBOL Differential Mode Output Balance OUT_+ to ...
Page 4
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic ELECTRICAL CHARACTERISTICS (continued 14.4V 5V load impedance from OUT_+ to OUT_ unless otherwise noted.) (Note 2) PARAMETER ...
Page 5
Dual Automotive, Audio Line Drivers DIGITAL CHARACTERISTICS (V = 14.4V 3.3V -40NC to +105NC, typical values are PARAMETER SYMBOL DIGITAL INTERFACE Input-Voltage High V Input-Voltage Low Input-Voltage Hysteresis Input ...
Page 6
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic ( V = 14.4V 5V 1kI, gain = 12dB SHUTDOWN CURRENT vs. TEMPERATURE 0.40 NO LOAD 0.35 INPUTS SHORTED V ...
Page 7
Dual Automotive, Audio Line Drivers ( V = 14.4V 5V 1kI, gain = 12dB GAIN ERROR vs. TEMPERATURE 0.020 0.015 0.010 0.005 LEFT CHANNEL 0 -0.005 -0.010 -0.015 RIGHT CHANNEL -0.020 -40 ...
Page 8
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic TOP VIEW PIN NAME 1 BIAS Analog Bias Voltage. Bypass BIAS to GND with a 10FF capacitor. Logic Supply Voltage. Connect capacitor ...
Page 9
Dual Automotive, Audio Line Drivers PIN NAME Address Inputs. Connect ADD0 and ADD1 ADD0 Connect ADD0 and ADD1 to GND for stand-alone mode. 15 SCL Serial Clock 16 SDA Serial-Data ...
Page 10
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic Table 2. Configuration Register Format ADDRESS FUNCTION CODE (HEX) D7 Configuration 0x00 DIAG Register DIAG: Set DIAG enable diagnostic mode. Write '0' to disable diagnostic ...
Page 11
Dual Automotive, Audio Line Drivers Table 4. General Fault Register Format ADDRESS FUNCTION CODE (HEX) D7 General Fault 0x02 x Register TWARN: The TWARN bit is set to ‘1’ when the temperature warning threshold is reached. TSHDN: The TSHDN is ...
Page 12
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic Table 7. Flag Register Format ADDRESS FUNCTION CODE D7 (HEX) FLAG 0x05 FLAG Register FLAG: FLAG bit is set to ‘1’ when the FLAG output is logic-low. The ...
Page 13
Dual Automotive, Audio Line Drivers Table 10. Right-Channel Mask Register ADDRESS FUNCTION CODE D7 (HEX) Right-Channel 0x08 MSVDDR Mask Register MSVDDR: Set MSVDDR enable the short to V MSGNDR: Set MSGNDR enable the short ...
Page 14
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic Output Short to GND When in diagnostic mode, the MAX13325/MAX13326 detect if any of the differential outputs is shorted to ground. Upon detection of the short to ground, ...
Page 15
Dual Automotive, Audio Line Drivers When in diagnostic mode with mute enabled, if there is excessive offset on any output, the MAX13325/ MAX13326 reports the condition through the I face and the FLAG output. See Table 14. When in diagnostic ...
Page 16
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic Table 17. Overvoltage Diagnostic FAULT CONDITION STATUS REPORT FLAG is asserted low. FLAG bit set. See Table 7. DUMP bit is set in the GFAULT register. See Table ...
Page 17
Dual Automotive, Audio Line Drivers START and STOP Conditions A master device initiates communication by issuing a START condition, which is a high-to-low transition on SDA with SCL high. A START condition from the master signals the beginning of a ...
Page 18
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic of an unsuccessful data transfer, the bus master may retry communication. The master must pull down SDA during the 9th clock cycle to acknowledge receipt of data when ...
Page 19
Dual Automotive, Audio Line Drivers SLAVE ADDRESS SLAVE ADDRESS Figure 7. A Single-Byte Read Operation SLAVE ADDRESS SLAVE ADDRESS Figure 8. A ...
Page 20
Dual Automotive, Audio Line Drivers 2 with I C Control and Diagnostic Power-Supply Bypass Capacitor (C3) The power-supply bypass capacitor (see the Typical Operating Circuit) lowers the output impedance of the power supply, and reduces the impact of the MAX13325/ ...
Page 21
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 2010 Maxim Integrated Products © ...