MAX9693 Maxim, MAX9693 Datasheet
MAX9693
Available stocks
Related parts for MAX9693
MAX9693 Summary of contents
Page 1
... The ultra-fast operation makes signal processing possi- ble at frequencies in excess of 600MHz. The MAX9692/MAX9693 feature a latch-enable (LE) function that allows the comparator to be used in a sample-hold mode. When LE is ECL high, the compara- tor functions normally. When LE is driven ECL low, the ...
Page 2
... SO (derate 7.4mW/°C above +70°C)..................588.2mW Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
... from 10mV to 100mV DSP +25° (± MIN MAX pw(LE Note 2 (MAX9693 only) PDM , unless otherwise noted.) MIN TYP = +25° MIN MAX = +25° MIN MAX MIN TYP 1.2 500 100 150 1.0 0.5 ...
Page 4
Single/Dual, Ultra-Fast, ECL-Output Comparators with Latch Enable (V = +5V -5.2V 50Ω WORST-CASE PROPAGATION DELAY vs. INPUT OVERDRIVE 1400 1200 1000 800 600 400 ...
Page 5
... MAX9691/3- 100mV 10mV OD Q OUT 200mV/div Q OUT 200mV/div NAME MAX9693 11 V Positive Supply. Bypass to GND with a 0.1µF capacitor. CC — IN+ Positive Input — IN- Negative Input 6 V Negative Supply. Bypass to GND with a 0.1µF capacitor. EE — Q OUT ...
Page 6
... GND2 biases the ECL output stage. If the LE function is not used, connect the LE pin to GND (MAX9692/MAX9693) and the complementary LE to ECL logic high level (MAX9693 only). Do not leave the inputs of an unused comparator floating for the MAX9693. Input Slew-Rate Requirements ...
Page 7
... A minimum latch pulse width of t tion, and the output transitions occur after a time t The MAX9691/MAX9692/MAX9693 will not false trip (i.e., output invert) if one of the inputs is in the valid common-mode range while the other input is outside the common-mode range. ...
Page 8
... P Propagation Delay Dispersion. The change in DSP propagation delay as a result of the overdrive of the input signal varying. t Propagation Delay Match (MAX9693 only). pdm The difference in propagation delay between two separate channels. Ordering Information (continued) TEMP PART ...
Page 9
... OUTLINE NO. U8+1 S8+2 P8+5 U10+2 E16+1 S16+3 P16+1 Pin Configurations MAX9691 GND1 CC IN GND2 IN OUT OUT EE DIP/SO/µMAX MAX9693 Q OUTA OUTB Q OUTA OUTB GND 3 14 GND LEA 4 13 LEB LEA 5 12 LEB INA- 7 ...
Page 10
... Comparators with Latch Enable For the latest package outline information and land patterns (footprints www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing per- tains to the package regardless of RoHS status ...
Page 11
... Single/Dual, Ultra-Fast, ECL-Output For the latest package outline information and land patterns (footprints www.maxim-ic.com/packages. Note that a "+", "#", or "-" in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing per- tains to the package regardless of RoHS status ...
Page 12
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed ...