TB6561FG Toshiba, TB6561FG Datasheet
TB6561FG
Specifications of TB6561FG
Available stocks
Related parts for TB6561FG
TB6561FG Summary of contents
Page 1
... TOSHIBA Bi-CMOS Integrated Circuit Silicon Monolithic Dual Full-Bridge Driver IC for DC Motors The TB6561FG is a dual bridge driver IC for DC brush motor that contains MOS transistors in an output stage. By using low ON-resistance MOS transistors and PWM current control circuitry, the driver achieves high efficiency. ...
Page 2
... (Note (Peak) 1.5 (Note −0.3 to 5.5 VIN V P 2.5 (Note − °C opr −55 to 150 T °C stg Symbol Rating TB6561FG OUT1A OUT2B V OUT1B CC 16,22,23, P-GNDB N.C.: 12pin, 19pin Unit V 2010-08-17 S-GND 7, 8,9,15 S-GND ...
Page 3
... V CC (opr) Input 0-V/5-V signal, Built in pull-down resistance (100 kΩ (typ.)). Input 0-V/5-V signal, Built in pull-down resistance (100 kΩ (typ.)). Input 0-V/5-V signal, Built in pull-down resistance (100 kΩ (typ.)). V CC (opr) 3 TB6561FG Remarks ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ⎯ ...
Page 4
... O ⎯ (L) O ⎯ 1mA reg reg ⎯ V CLD(H) = 50μ ⎯ V CLD(L) ⎯ I (Design guarantee) SD (OFF) ⎯ T (Design guarantee TB6561FG Min Typ. Max ⎯ 5.5 10 ⎯ 5.0 9 ⎯ 5.5 10 ⎯ 1.5 3 ⎯ ⎯ 2.3 5.5 ⎯ ⎯ −0.2 0.8 ⎯ ⎯ 0 ⎯ ⎯ ...
Page 5
... OFF (high-impedance OFF (high-impedance) L CLD Output H L OFF time OFF time 50 μs 50 μs (typ.) (typ.) 10 μs (typ.) TSD 5 TB6561FG Output Mode Short brake CW/CCW Short brake CCW/CW Short brake Stop Standby 2010-08-17 ...
Page 6
... T SD ΔT = 40°C (target spec OUT1 M P-GND PWM ON → OFF t2 = 500 ns (typ OUT1 P-GND PWM TB6561FG V CC OUT1 M P-GND PWM OFF P-GND P-GND ) reaches 160°C (typ.), the j 2010-08-17 ...
Page 7
... OUTPUT UPPER SIDE Iout – VCE(sat) <Reference data> 2.0 1.5 1.0 0 0.25 0.50 0.75 OUTPUT CURRENT Iout (A) 50 μs 50 μs (typ.) (typ.) 10 μs 10 μs (typ.) (typ.) OUTPUT LOWER SIDE Iout – VCE(sat) <Reference data> 2.0 1.5 1.0 0.5 0 1.00 1.25 1. TB6561FG 0.25 0.50 0.75 1.00 1.25 OUTPUT CURRENT Iout (A) 2010-08-17 1.50 ...
Page 8
... PWMA IN1A 5 6 IN2A TB6561FG PWMB 27 IN1B 26 IN2B 25 CLD S-GND 9,15,16,22,23,24,30 and P-GND as close as possible to the IC and GND lines since the IC may be destroyed TB6561FG (Note OUT1A 11 Motor OUT2A 14 P-GNDA 13 (Note 4) OUT1B 20 Motor OUT2BA 17 P-GNDB 18 (Note 4) line. ...
Page 9
... Package Dimensions Weight: 0.63 g (typ.) 9 TB6561FG 2010-08-17 ...
Page 10
... Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 10 TB6561FG 2010-08-17 ...
Page 11
... If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 11 TB6561FG ) J 2010-08-17 ...
Page 12
... Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 12 TB6561FG 2010-08-17 ...