TB6593FNG Toshiba, TB6593FNG Datasheet
TB6593FNG
Specifications of TB6593FNG
Available stocks
Related parts for TB6593FNG
TB6593FNG Summary of contents
Page 1
... Toshiba Bi-CD Integrated Circuit Silicon Monolithic Driver IC for DC motor TB6593FNG is a driver IC for DC motor with output transistor in LD MOS structure with low ON-resistor. Two input signals, IN1 and IN2, can choose one of four modes such as CW, CCW, short break, and stop mode. ...
Page 2
... Standby signal input “L” = Standby/200 kΩ pull-down at internal VM supply 13.5 V Output1 Power GND Output2 VM supply 13.5 V Control signal input 1 200 kΩ pull-down at internal Control signal input 2 Small signal supply Vcc = 2 5 TB6593FNG VM4 17 VM3 16 VM1 4 VM2 ...
Page 3
... Cu箔面積≧40% ③ Mounted on Glass-Epoxy Board, ③基板実装時 (76.2 mm × 114.3 mm × 1.6 mm, Cu film PCB面積 76.2×114.3×1.6mm area ≥ Cu箔面積≧30% 100 150 Ta (℃) 3 TB6593FNG Remarks Duty less. 2010-05-26 ...
Page 4
... L L Short break Short break OFF H Stop (High impedance) OFF L Standby (High impedance) VM OUT1 OUT2 M GND <OFF> OUT2 OUT1 M GND <OFF> TB6593FNG VM OUT2 OUT1 M GND <Short break> OUT2 M GND <ON> GND 2010-05-26 VM GND ...
Page 5
... VIN = 0 V VIH(STB) VIL(STB) IIH(STB) VIN = 3 V IIL(STB) VIN = 0 V Vsat(U+ IL( Vout = 15 V IL( Vout = 0 V VF( VF(L) UVLD (Designed value) UVLC TSD (Designed value) ΔTSD 5 TB6593FNG Min Typ. Max Unit ― 0.9 1.2 mA ― ― 1 μA ― ― ― Vcc+0.2 V -0.2 ― 0.8 ...
Page 6
... C4 to ～5.5V STBY 0.1uF 10uF Note: Bypass capacitors (C1, C2, C3, and C4) should be connected as close as possible to the IC. Vcc UVLO 20 Standby 3 IN1 18 TSD IN2 Control 19 Logic PWM 2 GND 1 6 TB6593FNG VM4 VM3 16 10uF VM1 0.1uF 4 VM2 H- Driver PGND1 8 ...
Page 7
... Package Dimensions Weight: 0.09 g (Typ.) 7 TB6593FNG 2010-05-26 ...
Page 8
... Otherwise, the current or power consumption may exceed the absolute maximum rating, and exceeding the rating(s) may cause the device breakdown, damage or deterioration, and may result injury by explosion or combustion. In addition, do not use any device that is applied the current with inserting in the wrong orientation or incorrectly even just one time. 8 TB6593FNG 2010-05-26 ...
Page 9
... If the current sink capability of the power supply is small, the device’s motor power supply and output pins might be exposed to conditions beyond maximum ratings. To avoid this problem, take the effect of back-EMF into consideration in system design. 9 TB6593FNG ) J 2010-05-26 ...
Page 10
... Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product. Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of noncompliance with applicable laws and regulations. 10 TB6593FNG 2010-05-26 ...