BTS 5210L Infineon Technologies, BTS 5210L Datasheet
BTS 5210L
Specifications of BTS 5210L
Related parts for BTS 5210L
BTS 5210L Summary of contents
Page 1
Product Summary • • • • • • • • • • • • • • • • • • • • • • • • • AEC qualified • Green product (RoHS compliant) Data Sheet Smart High-Side Power Switch ...
Page 2
Data Sheet control and protection circuit equivalent to channel 1 2 Smart High-Side Power Switch BTS5210L V1.1, 2007-05-29 ...
Page 3
Pin Definitions and Functions Pin Symbol Function 1 GND Ground of chip 2 IN1 Input 1,2 activates channel 1,2 in case of logic high signal 4 IN2 3 ST1 Diagnostic feedback 1 & channel 1,2 open drain, low ...
Page 4
Parameter Supply voltage (overvoltage protection see page 6) Supply voltage for full short circuit protection T = -40 ...+150°C j,start Load current (Short-circuit current, see page 6) ) Load dump protection 1 V LoadDump = 2 Ω ...
Page 5
Parameter and Conditions Thermal resistance junction - Case 6) junction – ambient cooling area Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching Capabilities ...
Page 6
Parameter and Conditions, = -40...+150° unless otherwise specified j bb Operating Parameters Operating voltage ) Undervoltage switch off 9 ) Overvoltage protection Standby current ...
Page 7
Parameter and Conditions -40...+150° unless otherwise specified j bb Reverse Battery ) 16 Reverse battery voltage Drain-source diode voltage = - 2 +150° Diagnostic Characteristics Open load ...
Page 8
Truth Table ( each channel ) Normal operation Open load Overtemperature L = "Low" Level X = don't care H = "High" Level Status signal valid after the time delay shown in the timing diagrams Parallel switching of channel 1 ...
Page 9
Input circuit (ESD protection), The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Status output, ST1 or ST2 ESD-Zener diode: 6.1 V typ., max 0.3 mA 1.6 mA. The use of ESD ...
Page 10
GND disconnect with GND pull up Any kind of load > GND IN IN(T+) Due to V > low signal available. GND ST V disconnect with energized inductive bb load For ...
Page 11
Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2 = low EE RII ...
Page 12
Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 to channel 4 Figure 1a: V turn on: bb Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure ...
Page 13
Figure 3b: Turn on into short circuit: shut down by overtemperature, restart by cooling (two parallel switched channels 1 and 2) ST1 and ST2 have to be configured as a 'Wired OR' function ST1/2 with a single pull-up resistor. Figure ...
Page 14
Package Outlines ø0.8 x 0.1 -0.05 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Stand OFF 3) Stand OUT 4) Pin 1 Index Marking; Polish finish All package corners max. R 0.25 Figure 1 ...
Page 15
Revision History Version Date Changes V1.1 2007-05-29 Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features Package page Modification of the package to ...
Page 16
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...