BTS 6133D Infineon Technologies, BTS 6133D Datasheet
BTS 6133D
Specifications of BTS 6133D
Related parts for BTS 6133D
BTS 6133D Summary of contents
Page 1
... Limit for Charge pump unclamped ind. loads Level shifter Rectifier Output Voltage Logic detection Temperature sensor Page PROFET ® BTS 6133D V 5.5 ... 38 bb(on L(nom) I L(ISO) I L12(SC) 3 & Tab + OUT I L Current Sense Load ...
Page 2
... Output; output to the load; pin 1 and 5 must be externally shorted 13 12V T =150 ° ≤ 16V : > 16V bb Page PROFET ® BTS 6133D Symbol Values Load dump I self-limited L T -40 ...+150 j -55 ...+150 T stg P tot ...
Page 3
... I j L(nom OUT OUT off dV /dt =-40...150 °C j -dV/dt =-40...150 ° (one layer, 70µm thick) copper area for V bb Page PROFET ® BTS 6133D Values min typ max -- -- 1 Values min typ max -- ...
Page 4
... IS T =25 ° =150 ° kΩ, T =25 ° =150 ° ° 150 ° (+V > out bb Page PROFET ® BTS 6133D Symbol Values min typ 5.5 -- bb(on 2.5 bIN( bb(ucp bb(off ...
Page 5
... T j(start) 13) =-40°C: = 30V T j(start) =25°C: T j(start) =+150°C: T j(start -40...+150° prior to shutdown, see also figures 3.x on page 13. d(SC1) Page PROFET ® BTS 6133D Symbol Values min typ I -- 110 L6(SC) -- 105 L12(SC ...
Page 6
... IN L IS(LH) after input IS static t son(IS) 17) t slc(IS -40...+150° Z,IS >1V typ.), overtemperature and short circuit; see also truth ON Page PROFET ® BTS 6133D Values Unit min typ max -- 10 000 -- 8300 10000 11000 8300 9700 10600 8300 9300 10000 7500 ...
Page 7
... V unless otherwise specified j bb Input Required current capability of input switch Input current for turn-off Data Sheet Symbol I IN(on) T =-40..+150° =-40..+150° IN(off) Page PROFET ® BTS 6133D Values Unit min typ max -- 1.4 2 µA Rev. 1.0, 2007-02 ...
Page 8
... high impedance, potential depends on external circuit OUT 1 OUT > 3.5V (typ.) . See also page 11 and therefore also the sense current L Page PROFET ® BTS 6133D Current Sense I IS ≈ IS(LL) nominal ≈ IS(LL) I IS,fault ≈ IS(LL) I IS,fault ≈ ...
Page 9
... nominal. Note that when overvoltage exceeds 67 V typ. a voltage above 5V can occur between IS and GND Z,VIS = I /k can ilis . can reach IS Page PROFET ® BTS 6133D V Z1 PROFET = 42 V typ ON(Cl Z,IN Z,IS IN Logic PROFET Z,VIS ...
Page 10
... For higher clamp voltages currents at IN and IN IS have to be limited to 120 mA. Version a: OUT Power Transistor R L Power GND . − OUT V + OUT IS(LH) Page PROFET ® BTS 6133D OUT IN PROFET IS Rev. 1.0, 2007-02 +V < ...
Page 11
... Maximum allowable load inductance for single switch off j,start = 150° Ω 1000 100 10 30V 0 0,01 300 [mOhm] Page PROFET ® BTS 6133D OUT PROFET · · ...
Page 12
... IN V OUT dV/dtoff off t slc(IS long as V bIS < V Z,IS the sense current will never exceed I IS,fault and/or I IS,lim . t t soff(IS) Figure 2b: Switching an inductive load OUT Page PROFET ® BTS 6133D IS,faut IS,lim V ON(CL) Rev. 1.0, 2007- ...
Page 13
... Shut down remains latched until next reset via input. Figure 4a: Overtemperature Reset ON(SC OUT Page PROFET ® BTS 6133D Internal Switch off t d(SC2) depending on the external impedance 1V typ IS,fault k ilis < IS,fault Auto Restart Rev ...
Page 14
... Approximate solution for worst case, minimum detectable load current: V ON(CL This range for the current sense ratio refers to all devices. The accuracy of the k means of calibration the value of k single device. Page PROFET ® BTS 6133D I IS,lim ILIS · ...
Page 15
... To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb- free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). Data Sheet BTS 6133D Page PROFET ® BTS 6133D Rev. 1.0, 2007-02 ...
Page 16
... Revision History Version Date Changes Rev. 1.0 2007-02-21 RoHS-compliant version of BTS6133D Page 1, page 16: RoHS compliance statement and Green product feature added Page 1, page 16: Change to RoHS compliant package PG-TO252-5-11 Legal disclaimer updated Data Sheet Page PROFET ® BTS 6133D Rev. 1.0, 2007-02 ...
Page 17
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...