HIP2500 Harris Corporation, HIP2500 Datasheet
HIP2500
Available stocks
Related parts for HIP2500
HIP2500 Summary of contents
Page 1
... HIP2500. The HIP2500IB drives high side and low side refer- enced power switches just like the HIP2500IP. The HIP2500IP1 lead Plastic DIP form of the HIP2500. Pins 4 and 5 removed from lead frame to provide extra creep- age and strike distances in high voltage applications. ...
Page 2
... See Figure 8 for logic supply voltages other than 15.0V. HIP2500 Thermal Information Unless Otherwise Noted. SS -0. +18.0V Thermal Resistance (Note 1, Typical HIP2500IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HIP2500IP1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HIP2500IB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +0.5V See Maximum Power Dissipation vs Temperature Curve B Junction Temperature Range . . . . . . . . . . . . . . . . . -40 +0.5V Storage Temperature Range Operating Ambient Temperature Range, T +0.5V DD +10V to V ...
Page 3
... Offset Supply Operating Transient Logic Truth Table HIN LIN HIP2500 + SYMBOL MIN TYP = 1000pF L t 320 420 ON t 260 385 OFF 250 365 ...
Page 4
... SWITCHING FREQUENCY (kHz) NOTE: All switching losses assumed IC. FIGURE 3. LOW VOLTAGE POWER DISSIPATION vs FREQUENCY 10 500V 400V 300V 1.0 0 TEMPERATURE ( FIGURE 5. OFFSET SUPPLY LEAKAGE vs TEMPERATURE HIP2500 1.0 V BIAS 0.1 0.01 0.001 FIGURE 2. HIGH VOLTAGE POWER DISSIPATION vs SWITCHING FREQUENCY 6 MAX V ...
Page 5
... JUNCTION TEMPERATURE ( FIGURE 9. QUIESCENT V SUPPLY CURRENT vs BS TEMPERATURE 3.0 -40 0 2.5 25 125 2.0 1.5 1.0 - 0.5 125 SOURCE/SINK DRAIN-SOURCE VOLTAGE FIGURE 11. DRIVER SINK/SOURCE V-I CHARACTERISTIC HIP2500 (Continued 100 120 140 5 C) FIGURE 8. INPUT LOGIC THRESHOLD vs SUPPLY VOLTS ...
Page 6
... FIGURE 15. PROPAGATION DELAYS AT V Typical Application Diagram HIP2500 LEVEL UV V SHIFT DD HIN SD LOGIC LIN V SS HIP2500 (Continued) 460 440 420 400 380 360 340 320 300 FIGURE 14. PROPAGATION DELAY vs SUPPLY VOLTAGE - 100 ...
Page 7
... Dambar protrusions shall not exceed 0.010 inch (0.25mm the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). HIP2500 E14.3 (JEDEC MS-001-AA ISSUE D) 14 LEAD DUAL-IN-LINE PLASTIC PACKAGE SYMBOL ...
Page 8
... Dambar protrusions shall not exceed 0.010 inch (0.25mm the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). HIP2500 E16.3 (JEDEC MS-001-BB ISSUE D) 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE SYMBOL ...
Page 9
... The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of 0.61mm (0.024 inch) 10. Controlling dimension: MILLIMETER. Converted inch dimen- sions are not necessarily exact. HIP2500 M16.3 (JEDEC MS-013-AA ISSUE C) 16 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE M ...