6MBP150RTJ060 Fuji Electric holdings CO.,Ltd, 6MBP150RTJ060 Datasheet
6MBP150RTJ060
Available stocks
Related parts for 6MBP150RTJ060
6MBP150RTJ060 Summary of contents
Page 1
... SPECIFICATION Device Name : Type Name : Spec. No ‘ N.Matsuda ‘ Nishiura T.Fujihira ‘ K.Yamada IGBT - IPM 6MBP150RTJ060 MS6M 0677 Fuji Electric Co.,Ltd. Matsumoto Factory MS6M 0677 H04-004-07 ...
Page 2
Classi- Date fication Ind ’ enactment ’ 0 ...
Page 3
Package Outline Drawings Package type : P621 6-M5 ±0.1 2 ±0.3 3.22 2 φ2.5 (φ1~1.5) Details of control terminals 1 09 ± ±0 ...
Page 4
Pin Descriptions Main circuit Symbol P Positive input supply voltage. U Output (U). V Output (V). W Output (W). N Negative input supply voltage contact. Control circuit No Symbol GNDU High side ground (U ALMU ...
Page 5
Block Diagram VccU VccU VinU VinU ALMU ALMU 1.5k 1.5k ALM ALM GNDU GNDU VccV VccV VinV VinV ALMV ...
Page 6
Absolute Maximum Ratings Tc=25°C unless otherwise specified. Items Bus Voltage (between terminal P and N) Collector-Emitter Voltage *1 Collector Current Collector Power Dissipation Supply Voltage of Pre-Driver *4 Input Signal Voltage *5 Input Signal Current Alarm Signal Voltage *6 ...
Page 7
Electrical Characteristics Tj=25°C, Vcc=15V unless otherwise specified. 5.1 Main circuit Item Collector Current at off signal input Collector-Emitter saturation voltage Forward voltage of FWD Turn-on time Turn-off time Reverse recovery time Maximum AvalancheEnergy (A non-repetition) 5.2 Control circuit Item ...
Page 8
Protection Section (Vcc=15V) Item Over Current Protection Level of Inverter circuit Over Current Protection Delay time SC Protection Delay time IGBT Chips Over Heating Protection Temperature Level Over Heating Protection Hysteresis Over Heating Protection Protection Temperature Level Over Heating ...
Page 9
Figure 1. Switching Time Waveform Definitions /Vin on Gate On Vge (Inside IPM) Fault (Inside IPM) normal /ALM Figure 2. Input/Output Timing Diagram Necessary conditions for alarm reset (refer to ① to ③ in figure2.) ① This ...
Page 10
ALM ALM Figure.4 Definition of tsc P VccU 20k IPM DC VinU U 15V SW1 GNDU V Vcc 20k DC W VinX 15V SW2 N GND Earth Figure 5. Noise Test Circuit Vcc Vcc P P ...
Page 11
Truth table 10.1 IGBT Control The following table shows the IGBT ON/OFF status with respect to the input signal Vin ...
Page 12
Cautions for design and application 1. Trace routing layout should be designed with particular attention to least stray capacity between the primary and secondary sides of optical isolators by minimizing the wiring length between the optical isolators and the ...
Page 13
’ ...
Page 14
... Scope of application 適用範囲 This specification is applied to the IGBT-IPM (type: 6MBP150RTJ060). 本仕様書は、IGBT-IPM (型式:6MBP150RTJ060)に適用する。 ...
Page 15
Circuit Characteristics(Respresentative) P ower sup ply current vs. Switching frequency Tc=1 25°C 70 P-side 60 N-side Switching frequency : Hz) Under voltage vs. Junc tion ...
Page 16
Circuit Characteristics (Representative) Collector curren Collec tor-Em itter voltag e Tj=25 °C(Chip) 240 Vcc=15V Vcc= 17V 200 160 120 0.5 1 1.5 2 Collector-Em itter voltage : Vce (V) Collector current vs ...
Page 17
Switching Loss vs. Collector Current Edc =30 0V,Vcc =15 V,Tj=25° 120 180 Coll ec tor current : Ic (A) Reversed b iased safe operating area Vcc=1 5V,Tj 125°C 400 ...
Page 18
Switching tim e vs. Collec tor current Edc =30 0V,Vcc=15 V,Tj=25°C 10000 1000 100 100 150 Col lector cu rrent : Ic (A) Revers e recovery characteris tic s trr,Irr vs.IF 100 100 ...
Page 19
Reliability Test Items Test cate- Test items gories 1 Terminal strength Pull force 端子強度 (Pull test) Test time 2 Mounting Strength Screw torque 締付け強度 Test time 3 Vibration Range of frequency 振動 Sweeping time Acceleration Sweeping direction Test ...
Page 20
Test cate- Test items gories 1 High temperature Test temp. reverse bias 高温逆バイアス Bias Voltage Bias Method Test duration 2 Temperature Test temp. humidity bias Relative humidity 高温高湿バイアス Bias Voltage Bias Method Test duration 3 Intermitted ON time operating ...
Page 21
This product shall be used within its absolute maximum rating (voltage, current, and temperature). This product may be broken in case of using beyond the ratings. 製品の絶対最大定格(電圧,電流,温度等)の範囲内で御使用下さい。絶対最大定格を超えて使用すると、素子が 破壊する場合があります。 2. Connect adequate fuse or protector of circuit between three-phase line ...
Page 22
Never add mechanical stress to deform the main or control terminal. The deformed terminal may cause poor contact problem. 主端子及び制御端子に応力を与えて変形させないで下さい。 端子の変形により、接触不良などを引き起こす場合が あります。 excessive static electricity is applied to the control terminals, the devices can be broken. Implement ...