SCA05010-BFN-LRN Shelly, Inc., SCA05010-BFN-LRN Datasheet
SCA05010-BFN-LRN
Related parts for SCA05010-BFN-LRN
SCA05010-BFN-LRN Summary of contents
Page 1
... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA05010-BFN-LRN : Version (A001) PCB VERSION: CHECKED BY DATE: ISSUE DATE ...
Page 2
NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Touch Screen Panel Specifications 9. Interface PIN Connections 10. Electro-Optical Characteristics 11. Inspection Criterion ...
Page 3
DATE PAGE 2009/06/26 P4 2009/09/07 P13 2009/09/11 front Update display mode and LCM drawing Add electro-optical Added version #A001 SUMMARY ...
Page 4
LCD MODULE PHYSICAL DATA General Description Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC Mechanical Description Item Number of dots LCM dimension TP outline TP active area Active area Dot size ...
Page 5
EXTERNAL DIMENSIONS ...
Page 6
BLOCK DIAGRAM G2 G480 R0-R07 G0-G7 B0-B7 VDD Backlight Circuit A1 A2 LCD 800(RGB)*480 HX8258-A×2+HX8662-C G1 G479 ...
Page 7
Touch Screen Panel(Top View) ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Power Supply Voltage(1) Power Supply Voltage(2) Power Supply Voltage(3) Input Voltage Supply voltage for LCD NOTE the module is used above these absolute maximum ...
Page 8
ELECTRICAL CHARACTERISTICS DC Characteristics Item Input high voltage Input low voltage Supply voltage(1) Supply voltage(2) Supply voltage(3) Current consumption for LCD normal operation Back-Light unit Item Current CIE Luminous Uniformity Ratio Bezel(BE) must be connected to ground ...
Page 9
TOUCH SCREEN PANEL SPECIFICATIONS 1.Electrical Characteristics Item Linearity Terminal Resistance Insulation Resistance Operating voltage Response Time Transmittance Note not operate it with a thing except a polyacetal pen(tip R0.8mm or less finger, especially those ...
Page 10
INTERFACE PIN CONNECTIONS NO. Symbol 1 VLED- 2 VLED+ 3 DGND 4 VDD ...
Page 11
NC 36 DGND Timing Requirement1 (TA =25ºC, AVDD=2.75V to 3.6V, DVSS= 0V, tr=tf=2ns) Timing Requirement2 No connection Ground TP pin ...
Page 12
Sync mode : (TA =25ºC, AVDD=2.75V to 3.6V, DVSS= 0V) Note : T +T < DEN mode ...
Page 13
WAVEFORM ...
Page 14
ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=3.3V, I Item Light angle（°） Temp（°C） Symbol Transmittance 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction ...
Page 15
Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the LCD panel in front of the light source. Measure the luminance on the LCD panel surface Definitions Lv ...
Page 16
Measuring procedure: Measure the luminance Li with the points in figure 1. Figure Active Area Uniformity value (Lu): min max( ) (4).CROSS-TALK Introduction： Crosstalk is an effect where the ...
Page 17
Pattern (valid for all greyscales): W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with the ...
Page 18
Definitions Panel colour coordinates according the CIE colour system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...
Page 19
Color Gamut Ratio (NTSC) related to NTSC’: NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness ...
Page 20
INSPECTION CRITERIA This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...
Page 21
Inspection standards 4.1 Major Defect Item Items to be inspected display 4.1.1 All 2) Display abnormally functional defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...
Page 22
Cosmetic Defect Item Items to be inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by ...
Page 23
Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...
Page 24
PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile, it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do ...
Page 25
LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it not alter, modify or change the shape of the tab ...
Page 26
Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust VLCD to show the best contrast. ( indispensable condition to drive LCD's within the specified voltage limit since the higher voltage then the ...