SCA01810-TFN-LNN Shelly, Inc., SCA01810-TFN-LNN Datasheet

Page 1

... INNOVATIVE DISPLAY TECHNOLOGIES I RVINE P: 949-417-8070/F: 949-417-8075 E-mail: Website: Part Number : Customer APPROVED BY: ( FOR CUSTOMER USE ONLY ) SOLD BY APPROVED BY 17171 M A URPHY VENUE , C 92614-5915 ALIFORNIA info@shellyinc.com www.shellyinc.com Specification SCA01810-TFN-LNN : PCB VERSION: CHECKED BY DATE: ISSUE DATE ...

Page 2

NO. 1. Cover 2. Record of Revision 3. LCD Module Physical Data 4. External Dimensions 5. Block Diagram 6. Absolute Maximum Ratings 7. Electrical Characteristics 8. Interface PIN Connections 9. Recommend Initial Code 10. Electro-Optical Characteristics 11. Inspection Criterion 12. ...

Page 3

DATE PAGE 09//30/09 3 RECORD OF REVISION Included version A701 SUMMARY ...

Page 4

LCD MODULE PHYSICAL DATA  General Description Display Type Display Mode Viewing Direction Connection Type Operation temperature Storage temperature Driving IC  Mechanical Description Item Number of dots LCM dimension LCD dimension Active area Dot size Dot pitch Backlight ...

Page 5

EXTERNAL DIMENSIONS ...

Page 6

BLOCK DIAGRAM /RESET /CS RS /WR / D15 IM0 VDD GND G1 LCD 128(BGR)*160 G159 ILI9163B G2 G160 ...

Page 7

Backlight Circuit  ABSOLUTE MAXIMUM RATINGS Item Operating temperature Storage temperature Logic input voltage range Supply voltage Driver supply voltage NOTE the module is used above these absolute maximum ratings. It may become permanently damaged. Using the module ...

Page 8

ELECTRICAL CHARACTERISTICS  DC Characteristics Item Input/Output Input high voltage Input low voltage Output high voltage Output low voltage Power & Operation Voltage Analog Operating voltage Gate Driver High voltage Gate Driver Low voltage Current consumption for LCD normal ...

Page 9

INTERFACE PIN CONNECTIONS NO. Symbol 1 GND 2 VDD 3 /CS 4 /RESET / ...

Page 10

RECOMMEND INITIAL CODE void init_ILI9163B write_command(0x11); // sleep out DelayX1ms(20); write_command(0x26); //Gamma set write_data(0x00,0x04); //write_command(0xf2); //E0h & E1h Enable/Disable //write_data(0x00,0x00); write_command(0xb1); //Frame Rate control write_data(0x00,0x07); write_data(0x00,0x14); write_command(0xc0); //Set VRH1[4:0] & VC[2:0] for VCI1 & GVDD write_data(0x00,0x0c); write_data(0x00,0x05);//0x0000 ...

Page 11

Scanning Direction write_data(0x00,0xc0); write_command(0xb7); //Set Source Output Direction write_data(0x00,0x00); write_command(0xf2); //E0h & E1h Enable/Disable write_data(0x00,0x01); write_command(0xe0); //Positive Gamma Correction Setting write_data(0x00,0x36); write_data(0x00,0x29); write_data(0x00,0x12); write_data(0x00,0x22); write_data(0x00,0x1c); write_data(0x00,0x15); write_data(0x00,0x42); write_data(0x00,0xb7); write_data(0x00,0x2f); write_data(0x00,0x13); write_data(0x00,0x12); write_data(0x00,0x0a); write_data(0x00,0x11); write_data(0x00,0x0b); write_data(0x00,0x06); write_command(0xe1); //Negative Gamma ...

Page 12

ELECTRO-OPTICAL CHARACTERISTICS Driving condition: VDD=2.8V, I Item Light angle（°） Temp（°C） Symbol Transmittance 0 Contrast ratio 0 Brightness 0 Luminance uniformity 0 (surface within panel) Cross talk 0 Rｘ Rｙ Gｘ Gｙ Chromaticity 0 Bｘ Bｙ Wｘ Wｙ Color Reproduction ...

Page 13

Measuring Equipment Measurement Point Diameter Measurement Point Location Light source Reflectance Plate Test pattern Contrast setting Measuring procedure: Transmittance: The light source is located at the backside of the panel. 1、 Measure the light source 2、 Place the LCD panel ...

Page 14

Measure the luminance Li with the points in figure 1. Figure Active Area Uniformity value (Lu): min max( ) (4)．CROSS-TALK Introduction： Crosstalk is an effect where the contrast of ...

Page 15

W: The width of the rectangle in the following pictures; 5mm 2*w=10mm Pattern A ● Definitions： Cross Talk Value： CTV = |LvA - LvB| / LvA * 100% Where： LvA: Luminance measured with the centre test point of pattern A ...

Page 16

Definitions Panel color coordinates according the CIE color system (CIE 1931). In general always requested to measure the X, Y and Z values. Here u´, v´ and L* are according CIE 1931 ...

Page 17

NTSC: =F (display)/F (NTSC’) NTSC’ primaries: Red Green Blue F (NTSC’) =74.42 12:00 9:00 6:00 Brightness x’ y’ 0.67 0.33 0.21 0.71 0.14 0.08 3:00 Brightness cure of selected segment B 2 Brightness curve of nonselected segment B 1 Driving ...

Page 18

INSPECTION CRITERION This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM. 1 Sample plan Sampling method shall be in accordance with MIL-STD-105D, inspection level II and based on: Major defect: AQL ...

Page 19

Inspection standards 4.1 Major Defect Item Items to be inspected display 4.1.1 All 2) Display abnormally functional defects 3) Missing vertical，horizontal segment 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing Missing ...

Page 20

Cosmetic Defect Item Items to be inspected No Line defect L(Length) Black line, White line, Foreign 4.2.2 material under polarizer, If the Polarizer scratch can be seen after mobile phone cover assembling or in the operating condition, judge by ...

Page 21

Cosmetic Defect Item Items to be inspected No (i) Chips on corner Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. (ii)Usual surface cracks ...

Page 22

PRECAUTIONS FOR USING LCD MODULES Handing Precautions (1) The display panel is made of glass and polarizer. As glass is fragile it tends to become or chipped during handling especially on the edges. Please avoid dropping or jarring. Do ...

Page 23

LCM has been assembled and adjusted with a high degree of precision, avoid applying excessive shocks to the module or making any alterations or modifications to it not alter, modify or change the shape of the tab ...

Page 24

Viewing angle varies with the change of liquid crystal driving voltage (VLCD). Adjust VLCD to show the best contrast. ( indispensable condition to drive LCD's within the specified voltage limit since the higher voltage then the ...