SCA01810-TFN-LNN Shelly, Inc., SCA01810-TFN-LNN Datasheet - Page 22

• Manufacturer Part Number: SCA01810-TFN-LNN
• Description: Innovative Display Technologies 17171 Murphy Avenue
• Manufacturer: Shelly, Inc.


Handing Precautions
during handling especially on the edges. Please avoid dropping or jarring. Do not subject it to a mechanical
shock by dropping it or impact.
your mouth. If the substance contacts your skin or clothes, wash it off using soap and water.
color tone to vary. Do not touch the display with bare hands. This will stain the display area and degraded
insulation between terminals (some cosmetics are determined to the polarizer).
this polarizer carefully. Do not touch, push or rub the exposed polarizer’s with anything harder than an HB
pencil lead (glass, tweezers, etc.). Do not put or attach anything on the display area to avoid leaving marks
on. Condensation on the surface and contact with terminals due to cold will damage, stain or dirty the
polarizer. After products are tested at low temperature they must be warmed up in a container before
coming is contacting with room temperature air.
dry cloth. If it is heavily contaminated, moisten cloth with one of the following solvents
Do not scrub hard to avoid damaging the display surface.
following.
Wipe off saliva or water drops immediately, contact with water over a long period of time may cause
deformation or color fading. Avoid contacting oil and fats.
water droplets, moisture condensation or a current flow in a high-humidity environment.
it is free of twisting, warping and distortion. In particular, do not forcibly pull or bend the I O cable or the
backlight cable.
should be paid to electrostatic discharge as for an ordinary CMOS IC. To prevent destruction of the
elements by static electricity, be careful to maintain an optimum work environment.
your body have the same electric potential. Be sure to ground the body when handling the LCD modules.
the AC power source for the soldering iron does not leak. When using an electric screwdriver to attach
LCM, the screwdriver should be of ground potentiality to minimize as much as possible any transmission
of electromagnetic waves produced sparks coming from the communicator of the motor.
under dry conditions. To reduce the generation of static electricity be careful that the air in the work is not
too dried. A relative humidity of 50%-60% is recommended. As far as possible make the electric potential
of your work clothes and that of the work bench the ground potential
peeling off this protective film since static electricity may be generated
PRECAUTIONS FOR USING LCD MODULES
(1) The display panel is made of glass and polarizer. As glass is fragile it tends to become or chipped
(2) If the display panel is damaged and the liquid crystal substance leaks out, be sure not to get any in
(3) Do not apply excessive force to the display surface or the adjoining areas since this may cause the
(4) The polarizer covering the display surface of the LCD module is soft and easily scratched. Handle
(5) If the display surface becomes contaminated, breathe on the surface and gently wipe it with a soft
(6) Solvents other than those above-mentioned may damage the polarizer. Especially, do not use the
(7) Exercise care to minimize corrosion of the electrode. Corrosion of the electrodes is accelerated by
(8) Install the LCD Module by using the mounting holes. When mounting the LCD module make sure
(9) Do not attempt to disassemble or process the LCD module.
(10) NC terminal should be open. Do not connect anything.
(11) If the logic circuit power is off, do not apply the input signals.
(12) Electro-Static Discharge Control，Since this module uses a CMOS LSI, the same careful attention
- Isopropyl alcohol
- Ethyl alcohol
- Water
- Ketone
- Aromatic solvents
- Before remove LCM from its packing case or incorporating it into a set, be sure the module and
- Tools required for assembling, such as soldering irons, must be properly grounded. make certain
- To reduce the amount of static electricity generated, do not conduct assembling and other work
- The LCD module is coated with a film to protect the display surface. Exercise care when
22 |
P a g e