MPQ24S24-50C Wall Industries,Inc., MPQ24S24-50C Datasheet - Page 3

• Manufacturer Part Number: MPQ24S24-50C
• Description: 50 W Dc-dc Converter 10-36 Vdc Input 24 Vdc Output At 2.5 A Quarter-brick Package
• Manufacturer: Wall Industries,Inc.

WALL INDUSTRIES, INC.
Table 1: Pin Assignments
Figure 1: Mechanical Dimensions
Mechanical Dimensions (Heatsink Option – “HS” suffix)
(888) 597-WALL
NOTES:
INTERPRET DIMENSION AND TOLERANCE
1. PIN TO PIN TOLERANCE: ±.010 [±0.25] MEASURED AT STANDOFF FEATURE ONLY, DATUM-B.
2. PIN DIAMETER TOLERANCE OF : ±.005 [±0.13] MEASUREMENT READING APPLIES
4. THERMAL TRANSFER PLATE MATERIAL: .040 [1.02] THICK, ALUMINUM ALLOY 3003-0,
3. UNLESS OTHERWISE SPECIFIED.
.XX=±.02[0.5] .XXX=±.010[0.25]
THIRD ANGLE PROJECTION
PIN DESIGNATION
.47 [11.9]
DO NOT SCALE DRAWING
TO AREA FROM INTERFACE-PLANE SURFACE DATUM-C TO END OF PIN ONLY.
PER: QQA 250/2 WITH BLACK SOFT SULFURIC ANODIZE FINISH.
UNLESS OTHERWISE SPECIFIED
INTERPRET DIMENSION AND TOLERANCE
.XX=±.02[0.5] .XXX=±.010[0.25]
THIRD ANGLE PROJECTION
1
2
3
4
5
6
7
8
Unit: inches [mm]
Unit: inches [mm]
DO NOT SCALE DRAWING
Pin #
PER ASME Y14.5M - 1994
ALL DIMENSONS ARE IN INCHES
[ XX ] ARE IN MILLIMETERS
1
2
3
4
5
6
7
8
PER ASME Y14.5M - 1994
APPLIED TOLERANCES:
ANGLES
+SENSE
+Vin
ON/OFF
-Vin
+Vout
TRIM
-SENSE
-Vout
ANGLES= ±1°
RECOMMENDED FINISHED RECEIVING PCB
STAND-OFF HOLE Ø.052±.003 [1.32±0.08]
±1
1
2
3
PIN Ø
Ø.062 [1.57]
Ø.040 [1.02]
Ø.062 [1.57]
Ø.062 [1.57]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.062 [1.57]
+Vin
Enable
-Vin
+Vout
+SENSE
TRIM
-SENSE
-Vout
.00 [0.0]
.005
Pin Name
Ø.040 [1.02] PINS ONLY 6X
STANDOFF DIMENSION
MAX SCREW DEPTH .100 FROM SURFACE-A 4X
.071±.005 [1.80±0.13]
C
LABEL
.26 [6.5]
DOT DENOTES
PIN-1
A
TORQUE: 6.0 lbf in [ 0.68 N m]
MAX APPLIED RECIEVING
1
2
3
.112(NO:4)-40UNC-2B 4X
Positive Input
Remote On/Off
Negative Input
Negative Output
Negative Remote Sense
Output Voltage Trim
Positive Remote Sense
Positive Output
1.860 [47.24]
2.00 [50.8]
.47 [11.9]
2.37 [60.2]
Function
.19 [4.7]
RECOMMENDED FINISHED RECEIVING PCB
STAND-OFF HOLE Ø.052±.003 [1.32±0.08]
1
2
3
PIN-2 SHOWN FOR DIMENSIONS
4
5
6
7
8
Ø.040 [1.02] PINS ONLY 4X
.19 [4.7]
STANDOFF DIMENSION
MAX SCREW DEPTH .100 FROM SURFACE-A 4X
.071±.005 [1.80±0.13]
www.wallindustries.com
PIN END
.00 [0.0]
.20 MIN [5.1 MIN]
SEE NOTE-4
SEE NOTE-3
PIN LENGTH FROM
INTERFACE-PLANE ONLY
.26 [6.5]
.005
.00 [0.0]
1.030 [26.16]
LABEL
DOT DENOTES
PIN-1
.51 [13.0]
B
TORQUE: 6.0 lbf in [ 0.68 N m]
C
INTERFACE-PLANE
-A-
MAX APPLIED RECIEVING
1
2
3
If not used, leave open for standard unit, short to –Vin on ‘R’ units.
If not used, short to –Vo.
If not used, leave open.
If not used, short to +Vo.
.112(NO:4)-40UNC-2B 4X
SEE NOTE-4
Rev. C
1.860 [47.24]
4
5
6
7
8
2.00 [50.8]
NOTES:
2.37 [60.2]
1. PIN TO PIN TOLERANCE: ±.010 [±0.25] MEASURED AT STANDOFF FEATURE ONLY, DATUM-B.
2. PIN DIAMETER TOLERANCE OF : ±.005 [±0.13] MEASUREMENT READING APPLIES
4. THERMAL TRANSFER PLATE MATERIAL: .040 [1.02] THICK, ALUMINUM ALLOY 3003-0,
3. STANDARD PIN LENGTH UNLESS OTHERWISE SPECIFIED.
TO AREA FROM INTERFACE-PLANE SURFACE DATUM-C TO END OF PIN ONLY.
PER: QQA 250/2 WITH BLACK SOFT SULFURIC ANODIZE FINISH.
.19 [4.7]
PIN DESIGNATION
1
2
3
4
5
6
7
8
.47 [11.9]
4
5
6
7
8
ON/OFF
+SENSE
+Vin
-Vin
+Vout
TRIM
-SENSE
-Vout
.19 [4.7]
TECHNICAL DATASHEET
PIN END
.20 MIN [5.1 MIN]
SEE NOTE-3
PIN LENGTH FROM
INTERFACE-PLANE ONLY
4
5
6
7
8
Comments
.51 [13.0]
.00 [0.0]
PIN Ø
Ø.040 [1.02]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.062 [1.57]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.040 [1.02]
Ø.062 [1.57]
MPQ24S24-50C
B
-A-
INTERFACE-PLANE
4
5
6
7
8
1
2
3
Page 3 of 11
.47 [11.9]