MC74HC541ADWG ON Semiconductor, MC74HC541ADWG Datasheet - Page 9

• Manufacturer Part Number: MC74HC541ADWG
• Description: IC BUFF/DVR TRI-ST 8BIT 20SOIC
• Manufacturer: ON Semiconductor
• Series: 74HCr

Specifications of MC74HC541ADWG

• Logic Type: Buffer/Line Driver, Non-Inverting
• Number Of Elements: 1
• Number Of Bits Per Element: 8
• Current - Output High, Low: 7.8mA, 7.8mA
• Voltage - Supply: 2 V ~ 6 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (7.5mm Width)
• Logic Family: 74HC
• Number Of Channels Per Chip: Octal
• Polarity: Non-Inverting
• Supply Voltage (max): 6 V
• Supply Voltage (min): 2 V
• Maximum Operating Temperature: 125 C
• Mounting Style: SMD/SMT
• High Level Output Current: - 7.8 mA
• Input Bias Current (max): 4 uA
• Low Level Output Current: 7.8 mA
• Maximum Power Dissipation: 500 mW
• Minimum Operating Temperature: - 55 C
• Number Of Lines (input / Output): 3
• Output Type: 3-State
• Propagation Delay Time: 80 ns @ 2 V or 30 ns @ 3 V or 18 ns @ 4.5 V or 15 ns @ 6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MC74HC541ADWG; MC74HC541ADWGOS

PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [e-mail]
ON Semiconductor and
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
e
20
1
0.13 (0.005)
Z
b
M
D
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
0.10 (0.004)
11
10
E
A
H
E
A
1
N. American Technical Support: 800−282−9855 Toll Free
Europe, Middle East and Africa Technical Support:
Japan Customer Focus Center
PACKAGE DIMENSIONS
USA/Canada
Phone: [phone]
Phone: 81−3−5773−3850
VIEW P
http://onsemi.com
CASE 967−01
SOEIAJ−20
F SUFFIX
M
ISSUE A
_
L
E
9
L
DETAIL P
Q
1
c
NOTES:
1.
2.
3.
4.
5.
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
Y14.5M, 1982.
MOLD FLASH OR PROTRUSIONS AND ARE
MEASURED AT THE PARTING LINE. MOLD FLASH
OR PROTRUSIONS SHALL NOT EXCEED 0.15
(0.006) PER SIDE.
REFERENCE ONLY.
INCLUDE DAMBAR PROTRUSION. ALLOWABLE
DAMBAR PROTRUSION SHALL BE 0.08 (0.003)
TOTAL IN EXCESS OF THE LEAD WIDTH
DIMENSION AT MAXIMUM MATERIAL CONDITION.
DAMBAR CANNOT BE LOCATED ON THE LOWER
RADIUS OR THE FOOT. MINIMUM SPACE
BETWEEN PROTRUSIONS AND ADJACENT LEAD
TO BE 0.46 ( 0.018).
DIM
H
A
A
D
L
M
b
c
E
e
L
Q
Z
E
E
DIMENSIONING AND TOLERANCING PER ANSI
CONTROLLING DIMENSION: MILLIMETER.
DIMENSIONS D AND E DO NOT INCLUDE
TERMINAL NUMBERS ARE SHOWN FOR
THE LEAD WIDTH DIMENSION (b) DOES NOT
1
1
12.35
MILLIMETERS
MIN
0.05
0.35
0.15
5.10
7.40
0.50
1.10
0.70
---
---
0
1.27 BSC
_
12.80
MAX
10
2.05
0.20
0.50
0.25
5.45
8.20
0.85
1.50
0.90
0.81
_
0.002
0.014
0.006
0.486
0.201
0.291
0.020
0.043
0.028
MIN
---
---
MC74HC541A/D
0
0.050 BSC
INCHES
_
MAX
0.081
0.008
0.020
0.010
0.504
0.215
0.323
0.033
0.059
0.035
0.032
10
_