STK433-120-E SANYO Semiconductor, STK433-120-E Datasheet
STK433-120-E
Related parts for STK433-120-E
STK433-120-E Summary of contents
Page 1
... Ordering number : EN*A1595 STK433-120-E Overview The STK433-120 hybrid IC designed to be used in 120W × 2ch class AB audio power amplifiers. Applications • Audio power amplifiers. Features • Pin-to-pin compatible outputs ranging from 80W to 150W. • Can be used to replace the STK433-000 series (30W to 60W/2ch) and STK433-200/-300 series (3-channel) due to its pin compatibility. • ...
Page 2
... The circuit is turned on by applying VBE (approximately 0.6V) or higher voltage to the standby pin (pin13). *8: A thermoplastic adhesive resin is used for this hybrid IC. Designated transformer power supply (MG-200 equivalent) STK433-120-E Symbol V CC max (0) When no signal R L ≥6Ω ...
Page 3
... Package Dimensions unit:mm (typ) 67.0 60.0 3.6 1 2.0 (16.0) 14 2.0=28.0 Internal Equivalent Circuit 3 8 Pre Driver CH1 SUB 10 STK433-120-E 9.0 (R1.8) 15 0.4 0.5 2.9 5 Pre Driver CH2 + - Bias Circuit 13 No. A1595-3/ ...
Page 4
... CC 100μF 100Ω/1W 100μF /100V /100V GND 100μF /100V -V CC Sample PCB Trace Pattern www.DataSheet4U.com STK433-120-E STK433-120-E Ch2 Ch2 Ch1 Ch1 +PRE SUB GND ST-BY OUT OUT 100pF 56kΩ ...
Page 5
... R33 C32 J1, J2, J3, J4, J5, J6, J8, J9 J7, JS2, JS3, JS4, JS5, JS7 JS8, JS9 JS6, JS10 JS1 www.DataSheet4U.com (*1) Capacitor mark “A” side is “-” (negative). (*2) STK433-100Sr (2ch AMP) doesn’t mount parts STK433-120-E PARTS RATING - - ERG1SJ101 100Ω,1W RN16S102FK 1kΩ, 1/6W RN16S563FK 56kΩ ...
Page 6
... Pin Assignments [STK433-000/-100/-200Sr & STK415/416-100Sr Pin Layout] 2ch class-AB STK433-030-E 30W/JEITA STK433-040-E 40W/JEITA STK433-060-E 50W/JEITA STK433-070-E 60W/JEITA STK433-090-E 80W/JEITA STK433-100-E 100W/JEITA STK433-120-E 120W/JEITA STK433-130-E 150W/JEITA 3ch class-AB STK433-230A-E 30W/JEITA STK433-240A-E 40W/JEITA STK433-260A-E 50W/JEITA STK433-270-E 60W/JEITA STK433-290-E 80W/JEITA STK433-300-E 100W/JEITA ...
Page 7
... Supply voltage ±V [Thermal Design Example for STK433-120 6Ω)] The thermal resistance, θc-a, of the heat sink for total power dissipation, Pd, within the hybrid IC is determined as follows. www.DataSheet4U.com Condition 1: The hybrid IC substrate temperature, Tc, must not exceed 125°C. ...
Page 8
... OUT OUT 56kΩ 56kΩ 6.8kΩ www.DataSheet4U.com Load short protection circuit +V CC GND -V CC STK433-120-E (when 1/8P O max. = 15W max. = 120W). θc-a < (125 − 50)/82 < 0.91 θc-a < (150 − 50)/82 − 1.8/4 < 0.77 Ch2 Ch2 Ch1 Ch1 Ch2 +PRE SUB GND ST-BY OUT OUT ...
Page 9
... IST max. (*2) The pop noise level when the power is turned on can be reduced by setting the time constant with a capacitor in operating mode. (*3) Determines the time constant at which the capacitor (*2) is discharged in standby mode. STK433-120-E Stand-by Circuit SW transistor in Pre Driver IC Δ ...
Page 10
... 3μH 3μH 4.7Ω 0.1μF 0.1μF 4.7Ω 4.7Ω/1W / =8Ω OUT STK433-120-E Ch2 Ch2 Ch1 Ch1 +PRE SUB GND ST-BY OUT OUT 100pF 56kΩ ...
Page 11
... SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellectual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides information as of November, 2009. Specifications and information herein are subject to change without notice. STK433-120-E PS No. A1595-11/11 ...