FMB461 Interpoint Corporation, FMB461 Datasheet
FMB461
Related parts for FMB461
FMB461 Summary of contents
Page 1
F EATURES • –55°C to +85°C operation • VDC volt input • attenuation 110 kHz to 50 MHz • Transient suppression • Compliant to MIL-STD-461C, CE03 Size (max.): Non-flanged case ...
Page 2
FM-461 EMI FILTER 1. AMP ABSOLUTE MAXIMUM RATINGS Input Voltage • VDC continuous Lead Soldering Temperature (10 sec per lead) • 300°C Storage Temperature Range (Case) • –55°C to +135°C Isolation • 100 megohm minimum ...
Page 3
EMI I >150 H Positive Input 1000 pF 50 Input Common 150 47 pF 0.65 P6KE47 Positive Input 50 Input Common 47 pF 500V +Vin Input Common The case ground connection should be as low an impedance as possible to ...
Page 4
FM-461 EMI FILTER 1. AMP Pin Designation 1 Positive Input 2 Positive Output 3 Case Ground 4 Output Common 5 Input Common Typical Performance Curves: 25° nominal Vin, unless otherwise specified. 90 CE03 Limit 70 50 ...
Page 5
Dot on top of case indicates pin one CASE H BOTTOM VIEW See Figures 29 – 34 for pin configurations. 2.125 max (53.98) CAUTION Heat from reflow or wave soldering may damage the device. Solder pins individually with heat application ...
Page 6
FM-461 EMI Filter: Screening – Standard of ES Solder Seal 1.120 (28.45) 0.960 (24.38) 0.040 dia (1.02) 0.560 (14.22) Solder Tip-off 0.160 (4.06) F IGURE C ASES BOTTOM VIEW CASE H3 Squared corner and dot on top of case indicate ...
Page 7
FMA-461and FMB-461 EMI Filter: Screening – Standard of ES Solder Seal 1.120 (28.45) 0.960 (24.38) 0.040 dia (1.02) 0.560 (14.22) Solder Tip-off 0.160 (4.06) F BOTTOM VIEW CASE H6 MHE Series: Screening – Standard or ES HR151 Series and HR152 ...
Page 8
CASE K Dot on top of case indicates pin one Flange Thickness: Cases K1, K2, K3 and MLP Series (K5) 0.060 (1.52) Cases K4, K5 (except MLP Series), K6, K7, and K8 0.067 +0.005/-0.007 (1.70 +0.13/-0.8) Materials Header Case K1 ...
Page 9
Flanged case: Designator required in Case Option position of model number. FM-461 EMI Filter: Screening – Standard or ES Solder Seal 1.115 (28.32) 0.955 (24.26) 0.040 dia (1.02) 0.555 (14.1) Solder Tip-off 0.155 (3.94) Flanged cases: Designator required in Case ...
Page 10
CASE K Flanged cases: Designator required in Case Option position of model number. FMA-461 and FMB-461 EMI Filters: Screening – Standard or ES Solder Seal 1.115 (28.32) 0.955 (24.26) 0.040 dia (1.02) 0.555 (14.1) Solder Tip-off 0.155 (3.94) Flanged case: ...
Page 11
QA SCREENING 85°C PRODUCTS TEST (85°C Products excluding HR products) PRE-CAP INSPECTION Method 2017 TEMPERATURE CYCLE (10 times) Method 1010, Cond. B, -55°C to 125°C CONSTANT ACCELERATION Method 2001, 500 g BURN-IN 96 hours at 70°C ambient (typical) FINAL ELECTRICAL ...