FA5502PM Fuji Electric holdings CO.,Ltd, FA5502PM Datasheet - Page 16

• Manufacturer Part Number: FA5502PM
• Description: Power Factor Correction
• Manufacturer: Fuji Electric holdings CO.,Ltd

(6) ON/OFF control circuit
(7) Output circuit
FA5502P/M
control circuit. The ON/OFF control circuit consists of a
comparator with hysteresis. To turn the IC from OFF
mode to operating mode, pull up the ON/OFF pin
voltage to 3.95V (typ.) or higher. On the other hand, to
turn the IC from operating mode to OFF mode, pull
down the ON/OFF pin to 2.80V (typ.) or lower.
off, and the CS pin and OUT pin go approximately 0V.
IC consumption current during OFF mode is 200µA
(max.) which is much smaller than at an operating
mode.
value of 500nA.
pin, the ON/OFF pin voltage must not exceed the VCC
pin voltage, even when start up or stop operation.
the ON/OFF pin is normally pulled up to Vcc pin
through 10k
to approximately Vcc voltage.
the high power terminal, independent of the IC power
terminal (VCC pin). This pin allows an independent
drive resistance when the power MOSFET is ON and
OFF. Suppose the drive resistance when ON and OFF
are Rg (on) and Rg (off),
parasitic capacitance between gate and drain may
swing the OUT pin (pin 8) of IC below 0V. If OUT pin
voltage falls below -0.3V, a current may flow to the
parasitic element in IC,
malfunction. In such a case, Schottky diode must be
connected between OUT pin and GND so as not to
allow a parasitic current to flow to IC.
of VCC pin, the voltage of VC pin must not exceed that
of VCC pin even start up or stop operation.
Fig.12 shows the configuration of the ON/OFF
In the OFF mode, the reference (REF) voltage is cut
The input current at ON/OFF pin is a very small
In the case that external signal is applied to ON/OFF
If ON/OFF operation is not made by external signal,
As shown in Fig.13, VC pin (pin 9) is configured as
At standby, the OUT pin is kept Low.
If the drain voltage of power MOSFET oscillates, a
If VC pin is fed with a source which is independent
Rg(on)=Rg1+Rg2
Rg(off)=Rg2
12
ON/OFF
Fig.12 ON/OFF control circuit
to 1M . Then ON/OFF pin voltage goes
3.95/2.80V
• • • • • (10)
• • • • • (9)
whereby the
REF circuit
Output circuit
IC may
(8) Undervoltage lockout circuit
(9) Compensation circuit for light load
16
prevent malfunction when the Vcc voltage drops.
When the Vcc voltage rises from 0V, this IC starts
operation at 16.5V (typ.). If the Vcc voltage drops after
the IC starts up, this IC stops operation at 8.9V(typ.).
When IC stops operation by undervoltage lockout
circuit, OUT pin and CS pin is kept low
error amplifier do not have offset voltage, the input
current to the converter is approximately zero under
condition that the PFC converter operates in no load.
But an actual multiplier and current error amplifier may
have offset voltage. If the offset voltage is negative,
the input current, which corresponds to the offset
voltage, flows into the converter even when the PFC
converter operates in no load. In this case, the PFC
output voltage rises abnormally because of too much
input current.
correction circuit for light load. The output voltage of
error amplifier is approximately 1.55V or higher in
normal operation.
operates. If there is a negative offset voltage, the
output voltage of error amplifier falls below 1.55V in
the case that the PFC converter operates in no load or
light load. Then, the offset voltage is corrected in the
multiplier circuit. Because of this operation, even
under no load or light load, the PFC output voltage
does not rise abnormally, but is always kept stable.
The amount of correction changes linearly according
to the output of error amplifier, which can make
operation stable.
This IC contains an undervoltage lockout circuit to
If the output of multiplier and the input of current
To avoid these, this IC has an automatic offset
If the output voltage drops below 1.55V, this circuit
Fig.14 shows the outline of the effect of this circuit.
Quality is our message
Quality is our message
Quality is our message
Quality is our message
VCC
OUT
GND
VC
Fig.13 Output circuit
10
9
8
7
Shottky
diode
Rg1
Rg2
C5