T370HW01V0 AU_OPTRONICS, T370HW01V0 Datasheet
T370HW01V0
Related parts for T370HW01V0
T370HW01V0 Summary of contents
Page 1
Tel.: +44 (0)1296-469770 ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and Redistribution Allowed PDF created with FinePrint pdfFactory Pro trial version 37.0” HDTV Color TFT-LCD Module (*) Preliminary Specifications Note: This Specification is subject to change ...
Page 2
No COVER CONTENTS RECORD OF REVISIONS 1 GENERAL DESCRIPTION 2 ABSOLUTE MAXIMUM RATINGS 3 ELECTRICAL SPECIFICATIONS 3-1 ELECTRICAL CHARACTREISTICS 3-2 INTERFACE CONNECTIONS 3-3 INPUT TIMING SPECIFICATIONS 3-4 SIGNAL TIMING WAVEFORMS 3-5 COLOR INPUT DATA REFERNECE 3-6 POWER SEQUENCE 4 OPTICAL ...
Page 3
Version Date 0.1 Sep. 26,’03 ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and Redistribution Allowed PDF created with FinePrint pdfFactory Pro trial version Record of Revision No Description First Draft (Preliminary) T370HW01 V.0 Ver0 http://www.fineprint.com Remark ...
Page 4
General Description This specification applies to the 37.0 inch Color TFT-LCD Module T370HW01. This LCD module has a TFT active matrix type liquid crystal panel 1920x1080 pixels, and diagonal size of 37.0 inch. This module supports 1920x1080 HDTV mode ...
Page 5
Absolute Maximum Ratings The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit. Parameter Logic/LCD Driving Voltage Signal Input Voltage BLU Input Voltage BLU Control Voltage Operating Temperature Storage Temperature Operating Ambient ...
Page 6
Electrical Specification 3-1 Electrical Characteristics The T460HW01 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input which powers the CCFL, is typically generated by ...
Page 7
Note: The design of the inverter must have specifications for the lamp in LCD Assembly. The performance of the Lamp in LCM, for example lifetime or brightness, is extremely influenced by the characteristics of the DC-AC Inverter. So all ...
Page 8
Interface Connections LCD Connector (CN1): FI-WE41P-HF(JAE) or equivalent LVDS Transmitter: PIN # Spec NAME GND 5 RxO0- 6 RxO0+ 7 RxO1- 8 RxO1+ 9 RxO2- 10 RxO2+ 11 GND 12 RxOC- 13 ...
Page 9
LVDS Order RCLKP1 RAP1 RBP1 RCP1 RDP1 RCLKP2 RAP2 RBP2 RCP2 RDP2 ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and Redistribution Allowed PDF created with FinePrint pdfFactory Pro trial version ...
Page 10
BACKLIGHT CONNECTOR PIN CONFIGURATION 1. Electrical specification No 1 Input Voltage 2 Input Current 3 Input Power 4 Input Protection Voltage 5 Output Working Voltage 6 Output Current * 7 Strike Voltage 8 Open Lamp Voltage 9 Oscillating Frequency ...
Page 11
Input specification 3-3 Input Timing Specifications This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications for it’s proper operation. l Timing Table ...
Page 12
Signal Timing Waveforms CLKP-CLKN (RSDS) tSETUP2 DIO1;SHL=H 50% DIO2;SHL=L D00P- D00N D01P- D01N D02P- D02N D03P- D03N D10P- D10N D11P- D11N D12P- D12N D13P- D13N D20P- D20N D21P- D21N D22P- D22N D23P- D23N ©Copyright AU Optronics, Inc. March, 2004 ...
Page 13
Color Input Data Reference The brightness of each primary color (red, green and blue) is based on the 8 bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below ...
Page 14
Power Sequence LCD Vcc Signal 170ms min. Lamp On ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and Redistribution Allowed PDF created with FinePrint pdfFactory Pro trial version 90% 10% 30 max, 1ms min. 0 min. ...
Page 15
Optical Specification Optical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes in a dark environment at 25℃. The values specified are at an approximate distance 50cm from the LCD surface at a ...
Page 16
Note: 1. Contrast Ratio (CR) is defined mathematically as: 1. Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all pixels displaying white. From more information see FIG 2. The variation in ...
Page 17
FIG. 2 Luminance FIG.3 Response Time The response time is defined as the following figure and shall be measured by switching the input signal for “black” and “white”. ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and ...
Page 18
FIG.4 Viewing angle ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and Redistribution Allowed PDF created with FinePrint pdfFactory Pro trial version T370HW01 V.0 Ver0 http://www.fineprint.com 17/25 ...
Page 19
Mechanical Characteristics The contents provide general mechanical characteristics for the model T460HW01. In addition the figures in the next page are detailed mechanical drawing of the LCD. Outline Dimension Bezel Area Active Display Area Weight Surface Treatment ©Copyright AU ...
Page 20
Drawing ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and Redistribution Allowed PDF created with FinePrint pdfFactory Pro trial version T370HW01 V.0 Ver0 http://www.fineprint.com 19/25 ...
Page 21
Reliability 6. Environment test condition No 1 High temperature storage test 2 Low temperature storage test 3 High temperature operation test 4 Low temperature operation test 5 Vibration test (non-operating) 6 Shock test (non-operating) 7 Vibration test (with carton) 8 ...
Page 22
International Standard 7-1. Safety 1. Standard for Safety of Information Technology Equipment, including Electrical Business Equipment. 2. Standard for Safety of Information Technology Equipment Including Electrical Business Equipment. 3. IEC 60950:1999, Third Edition European Committee for Electrotechnical Standardization (CENELEC) ...
Page 23
Packing (1) Label Sample TBD (2) Carton Label TBD (3) Carton Size TBD ©Copyright AU Optronics, Inc. March, 2004 All Rights Reserved. No Reproduction and Redistribution Allowed PDF created with FinePrint pdfFactory Pro trial version T370HW01 V.0 Ver0 http://www.fineprint.com ...
Page 24
PRECAUTIONS Please pay attention to the followings when you use this TFT LCD module. 9-1 MOUNTING PRECAUTIONS (1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure ...
Page 25
PRECAUTIONS FOR STRONG LIGHT EXPOSURE Strong light exposure causes degradation of polarizer and color filter. 9-5 STORAGE When storing modules as spares for a long time, the following precautions are necessary. (1) (2) 9-6 HANDLING PRECAUTIONS FOR PROTECTION FILM ...