B121EW03-V8 AUO, B121EW03-V8 Datasheet
B121EW03-V8
Related parts for B121EW03-V8
B121EW03-V8 Summary of contents
Page 1
... Preliminary Specifications ( V ) Final Specifications 12.1” WXGA Color TFT-LCD Module B121EW03 V8 Model Name Customer Checked & Approved by Note: This Specification is subject to change without notice. B121EW03 V8 Version 1.0 www.DataSheet4U.net Product Specification AU OPTRONICS CORPORATION Date Approved by Howard Lee Date Prepared by Pei-Ching Huang Date 12/03/2007 Date ...
Page 2
... Shock Test Spec: ............................................................................................................. 26 9. Reliability......................................................................................................... 27 10. Mechanical Characteristics ......................................................................... 28 10.1 LCM Outline Dimension................................................................................................. 28 10.2 Screw Hole Depth and Center Position ......................................................................... 30 11. Shipping and Package ................................................................................. 31 11.1 Shipping Label Format................................................................................................... 31 11.2 Carton package.............................................................................................................. 32 11.3 Shipping package of palletizing sequence ..................................................................... 32 12. Appendix: EDID description......................................................................... 33 B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Contents ...
Page 3
... Version and Date Page 0.1 2007/10/23 All First Edition for Customer 0.2 2007/11/23 5 CCFL Power consumption is 4.5W max CCFL Power consumption is 3.7W max 1.0 2007/12/03 All B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Record of Revision Old description Final Specification New Description Remark ...
Page 4
... The LCD module should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950 applied exemption. 14) The LCD module is designed so that the CCFL supplied by Limited Current Circuit (IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit. B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Otherwise the TFT Module may be ...
Page 5
... General Description B121EW03 Color Active Matrix Liquid Crystal Display composed of a TFT LCD panel, a driver circuit, and backlight system. The screen format is intended to support the WXGA (1280(H) x 800(V)) screen and 262k colors (RGB 6-bits data driver) without backlight inverter. All input signals are LVDS interface compatible. ...
Page 6
... White Luminance [cd/m I =6.0mA CCFL Viewing Angle [degree] Luminance Uniformity CR: Contrast Ratio Cross talk Response Time [msec] Chromaticity of color Coordinates (CIE 1931) NTSC B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION 262K colors ( RGB 6-bit ) + -20 to +60 RoHS Compliance Unit Conditions 2 ...
Page 7
... Note 2: The luminance uniformity of 5 or13 points is defined by dividing the maximum luminance values by the minimum test point luminance = δ δ B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Maximum Brightness of five points Minimum Brightness of five points ...
Page 8
... Note 4: Definition of Average Luminance of White (Y Measure the luminance of gray level points L (x) is corresponding to the luminance of the point X at Figure in Note (1). Note 5: Definition of contrast ratio: Contrast ratio is calculated with the following formula. Contrast ratio (CR)= B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Photo detector Field=2 ° ...
Page 9
... The output signals of BM-7 or equivalent are measured when the input signals are changed from “Black” to “White” (falling time) and from “White” to “Black” (rising time), respectively. The response time interval between the 10% and 90% of amplitudes. Refer to figure as below. "White" 100% 90% 10% 0% B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION "Black" " ...
Page 10
... The measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION the screen center, over a 180° horizontal and ≧ ...
Page 11
... The following diagram shows the functional block of the 12.1 inches wide Color TFT/LCD Module: (4 pairs LVDS) LCD BOARD RxIN0 RxIN1 RxIN2 RxCLKIN VDD GND LCD Connector(20pin) Hirose DF19L-20P-1H Mating type DF 19G-20S-1C or compatible B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION DRIVE LCD TFT ARRAY/CELL Controller 1280(R/G/ 800 DC-DC Converter Ref circuit Y-Driver X-Driver ...
Page 12
... Storage Temperature Storage Humidity Note (25 ) ℃ Note 2: Permanent damage to the device may occur if exceed maximum values Note 3: For quality performance, please refer to AUO IIS (Incoming Inspection Standard). Operating Range B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Min Vin -0.3 Min 3.0 Min ...
Page 13
... VDDrp Allowable Logic/LCD Drive Ripple Voltage Note 1: Maximum Measurement Condition: Black Pattern Note 2: Typical Measurement Condition: Mosaic Pattern Note 3: Measure Condition +5.0V (High to Low) Control Signal +12.0V SW1 SW MAG-SPST C2 1uF/25V 0V B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Min Typ Max Units 3.0 3.3 3.6 [Volt] - 0.8 [Watt] - [mA] 242 ...
Page 14
... Signal electrical characteristics are as follows; Parameter Condition Differential Input High Vth Threshold (Vcm=+1.2V) Differential Input Low Vtl Threshold (Vcm=+1.2V) Differential Input Vcm Common Mode Voltage Note: LVDS Signal Waveform Vth VSS B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Min - -100 0.4 Vcm Max Unit 100 [mV] [mV] - [V] VCC-1 ...
Page 15
... So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. Note 1: It should be employed the inverter which has “Duty Dimming”, if ICCFL is less than 4mA. B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION ...
Page 16
... The distortion rate of the waveform should be within √2 ±10%. * Inverter output waveform had better be more similar to ideal sine wave. Note edge-type BLU with single CCFL, the life-time define as the brightness decay to 50% of original value and under normal operation. B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION ×V ...
Page 17
... Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format 1st Line 800th Line B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION 1278 1279 ...
Page 18
... DE Display Timing VS Vertical Sync HS Horizontal Sync Note: Output signals from any system shall be low or High-impedance state when VDD is off. B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Red-pixel Data Each red pixel's brightness data consists of these 6 bits pixel data. Green-pixel Data Each green pixel's brightness data consists of these 6 bits pixel data ...
Page 19
... LVDS is a differential signal technology for LCD interface and high speed data transfer device. PIN# Signal Name 1 GND 2 VDD 3 VDD 4 VDD EDID 5 AGING 6 CLK EDID 7 DATA EDID 8 RxIN0N 9 RxIN0P 10 GND B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION PIN# Signal Name 11 RxIN1N 12 RxIN1P 13 GND 14 RxIN2N 15 RxIN2P 16 GND 17 RxCLKINN 18 RxCLKINP 19 GND 20 GND ...
Page 20
... Note1: Start from right side B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION 20 1 Connector ...
Page 21
... LVDS inputs are as following. The module uses a 100ohm resistor between positive and negative data lines of each receiver input Signal Input Pin No. 8 RxIN0- 9 RxIN0+ 11 RxIN1- 12 RxIN1+ 14 RxIN2- 15 RxIN2+ 17 RxCLKIN- 18 RxCLKIN+ B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION LVDS Receiver ...
Page 22
... Basically, interface timings should match the 1280x800 /60Hz manufacturing guide line timing. Parameter Frame Rate Clock frequency Period Vertical Active Section Blanking Period Horizontal Active Section Blanking Note: DE mode only B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Symbol Min. Typ 71.11 Clock T - ...
Page 23
... Timing diagram T CLOCK DOTCLK Input Invaild Data Data B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Input Timing Definition ( DE Mode) Pixel Pixel Pixel Pixel Pixel Invaild N-1 N Data T VD Pixel ...
Page 24
... VDD power and lamp on/off sequence is as follows. Interface signals are also shown in the chart. Signals from any system shall be Hi-Z state or low level when VDD is off. 10% Power Supply VDD LVDS Interface Backlight On Power Sequence Timing Parameter B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION T1 90% T2 VALID DATA T5 Value Min. Typ. Max. 0.5 - ...
Page 25
... These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation Manufacturer Type / Part Number Mating Type / Part Number 7.3 Signal for Lamp connector Pin # 1 2 B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION For Signal Connector DF19LA-20P-1H MSB24013P20A or compatible For Lamp Connector BHSR-02VS-1 SM02B-BHSS-1-TB Cable color ...
Page 26
... Minutes each Axis ( 8.2 Shock Test Spec: Test condition: Acceleration: 180 G , Half sine wave Active time Pulse: +/-X,+/-Y,+/-Z , one time for each side Remark: 1. Ambient condition Relative humidity : 40% ~ 70% 2. Non-packaged and Non-operation B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION ℃ ...
Page 27
... Thermal Shock Test ESD Note1: According to EN 61000-4-2, ESD class B: Some performance degradation allowed. No data lost . Self-recoverable. No hardware failures. Remark: MTBF (Excluding the CCFL): 30,000 hours with a confidence level 90% B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Required Condition Ta= 40℃, 90%RH, 300h Ta= 50℃, Dry, 300h Ta= 0℃ ...
Page 28
... Product Specification AU OPTRONICS CORPORATION 10. Mechanical Characteristics 10.1 LCM Outline Dimension B121EW03 V8 Version 1 ...
Page 29
... Product Specification AU OPTRONICS CORPORATION B121EW03 V8 Version 1 ...
Page 30
... Screw Hole Depth and Center Position Screw hole maximum depth, from side surface = 2.0 mm and 2.5 mm (Ref. drawing in 10.1/10.2) Screw hole center location, from front surface = 2.8 ± 0.3mm (Ref. drawing) Screw Torque: Maximum 2.2 kgf-cm B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION ...
Page 31
... Shipping and Package 11.1 Shipping Label Format CT:C AATB XXX B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Week code Manufactured MM/WW V.8 Model No: B121EW03 0AXXG AU Optronics MADE IN CHINA (S01) H/W: 0A F/W:1 Hardware Code Model name ...
Page 32
... Carton package The outside dimension of carton is 520 (L)mm x 370 (W)mm x 295 (H)mm 11.3 Shipping package of palletizing sequence B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION ...
Page 33
... Green x 1D Green Blue x 20 Blue y White x 21 White y 22 Established timing Established timing 2 25 Established timing 3 Standard timing # Standard timing #2 28 B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION Value HEX ...
Page 34
... LCD) Vertical Border 46 (zero for internal LCD) 47 Signal (non-intr, norm, no stero, sep sync, neg pol) 48 Detailed timing/monitor descriptor # B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION 01 00000001 01 00000001 01 00000001 01 00000001 01 00000001 01 00000001 01 00000001 01 00000001 01 00000001 01 00000001 01 ...
Page 35
... Manufacture P/N 71 Manufacture P/N 72 Manufacture P Manufacture P/N 75 Manufacture P/N Manufacture P/N 76 Manufacture P/N 77 Manufacture P Manufacture P/N 7A Manufacture P/N Manufacture P Extension Flag 7F Checksum B121EW03 V8 Version 1.0 Product Specification AU OPTRONICS CORPORATION 00 00000000 00 00000000 00 00000000 20 00100000 00 00000000 00 00000000 00 00000000 FE 11111110 00 00000000 41 01000001 55 01010101 4F 01001111 0A 00001010 20 00100000 20 00100000 ...