LM3S1607 Luminary Micro, Inc, LM3S1607 Datasheet - Page 110

• Manufacturer Part Number: LM3S1607
• Description: Lm3s1607 Arm Microcontroller
• Manufacturer: Luminary Micro, Inc

Reset
Reset
Type
Type
System Control
Sleep Mode Clock Gating Control Register 1 (SCGC1)
Base 0x400F.E000
Offset 0x114
Type R/W, reset 0x00000000
110
Bit/Field
reserved
31:20
19
18
17
16
15
RO
RO
31
15
0
0
I2C1
R/W
RO
Register 27: Sleep Mode Clock Gating Control Register 1 (SCGC1), offset
0x114
This register controls the clock gating logic. Each bit controls a clock enable for a given interface,
function, or unit. If set, the unit receives a clock and functions. Otherwise, the unit is unclocked and
disabled (saving power). If the unit is unclocked, reads or writes to the unit will generate a bus fault.
The reset state of these bits is 0 (unclocked) unless otherwise noted, so that all functional units are
disabled. It is the responsibility of software to enable the ports necessary for the application. Note
that these registers may contain more bits than there are interfaces, functions, or units to control.
This is to assure reasonable code compatibility with other family and future parts. RCGC1 is the
clock configuration register for running operation, SCGC1 for Sleep operation, and DCGC1 for
Deep-Sleep operation. Setting the ACG bit in the Run-Mode Clock Configuration (RCC) register
specifies that the system uses sleep modes.
30
14
0
0
reserved
RO
RO
29
13
reserved
reserved
0
0
TIMER3
TIMER2
TIMER1
TIMER0
Name
I2C0
R/W
RO
28
12
0
0
RO
RO
27
11
0
0
Type
R/W
R/W
R/W
R/W
RO
RO
RO
RO
26
10
0
0
reserved
RO
RO
Reset
25
0
9
0
0
0
0
0
0
0
reserved
Preliminary
RO
RO
24
0
8
0
Description
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
Timer 3 Clock Gating Control. This bit controls the clock gating for
General-Purpose Timer module 3. If set, the unit receives a clock and
functions. Otherwise, the unit is unclocked and disabled. If the unit is
unclocked, reads or writes to the unit will generate a bus fault.
Timer 2 Clock Gating Control. This bit controls the clock gating for
General-Purpose Timer module 2. If set, the unit receives a clock and
functions. Otherwise, the unit is unclocked and disabled. If the unit is
unclocked, reads or writes to the unit will generate a bus fault.
Timer 1 Clock Gating Control. This bit controls the clock gating for
General-Purpose Timer module 1. If set, the unit receives a clock and
functions. Otherwise, the unit is unclocked and disabled. If the unit is
unclocked, reads or writes to the unit will generate a bus fault.
Timer 0 Clock Gating Control. This bit controls the clock gating for
General-Purpose Timer module 0. If set, the unit receives a clock and
functions. Otherwise, the unit is unclocked and disabled. If the unit is
unclocked, reads or writes to the unit will generate a bus fault.
Software should not rely on the value of a reserved bit. To provide
compatibility with future products, the value of a reserved bit should be
preserved across a read-modify-write operation.
RO
RO
23
0
7
0
RO
RO
22
0
6
0
RO
RO
21
0
5
0
SSI0
R/W
RO
20
0
4
0
reserved
TIMER3
R/W
RO
19
0
3
0
TIMER2
UART2
R/W
R/W
18
0
2
0
TIMER1
UART1
R/W
R/W
17
0
1
0
June 02, 2008
TIMER0
UART0
R/W
R/W
16
0
0
0