FP1189 WJ Communications, FP1189 Datasheet
FP1189
Available stocks
Related parts for FP1189
FP1189 Summary of contents
Page 1
... DataSheet U .com Product Description The FP1189 is a high performance ½-Watt HFET (Heterostructure FET low-cost SOT-89 surface- mount package. This device works optimally at a drain bias and 125 mA to achieve +40 dBm output IP3 performance and an output power of +27 dBm at 1-dB compression, while providing 20.5 dB gain at 900 MHz. The device conforms to WJ Communications’ ...
Page 2
... FP1189 ½-Watt HFET S-Parameters (V S21, Maximum Stable Gain vs. Frequency DB(|S[2,1]|) DB(MSG Frequency (GHz) Note: Measurements were made on the packaged device in a test fixture with 50 ohm input and output lines. The S-parameters shown are the de-embedded data down to the device leads and represents typical performance of the device. ...
Page 3
... FP1189 ½-Watt HFET Application Circuit: 870 – 960 MHz (FP1189-PCB900S) CAP POR T ID Ohm DataSheet4U.com TM 14 mil GETEK ML200DSS (ε r The main microstrip line has a line impedance of 50 Ω. WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 ...
Page 4
... FP1189 ½-Watt HFET FP1189-PCB900S Application Circuit Performance Plots S11 vs. Frequency 0 -40c +25c -5 -10 -15 -20 -25 -30 860 880 900 920 Frequency (MHz) P1dB vs. Frequency -40c +25c 20 860 880 900 920 Frequency (MHz) OIP3 vs. Temperature freq = 915, 916 MHz ...
Page 5
... FP1189 ½-Watt HFET Application Circuit: 1930 – 1990 MHz (FP1189-PCB1900S) PORT Ohm CAP ID mil GETEKTM ML200DSS (εr = 4.2) DataSheet4U.com The main microstrip line has a line impedance of 50 Ω. WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 4 DataSheet U .com The application circuit is matched for output power. ...
Page 6
... FP1189 ½-Watt HFET FP1189-PCB1900S Application Circuit Performance Plots S11 vs. Frequency 0 -40C +25C -5 -10 -15 -20 -25 -30 1930 1950 1970 Frequency (MHz) P1dB vs. Frequency -40C +25C 20 1930 1950 1970 Frequency (MHz) OIP3 vs. Temperature freq = 1960, 1961 MHz ...
Page 7
... FP1189 ½-Watt HFET Application Circuit: 2110 – 2170 MHz (FP1189-PCB2140S) CAP PORT ID Ohm CAP ID= C10 C= 1.5 pF DataSheet4U.com TM 14 mil GETEK ML200DSS (ε = 4.2) r The main microstrip line has a line impedance of 50 Ω. WJ Communications, Inc Phone 1-800-WJ1-4401 FAX: 408-577-6621 ...
Page 8
... FP1189 ½-Watt HFET FP1189-PCB2140S Application Circuit Performance Plots S11 vs. Frequency 0 -40c +25c -5 -10 -15 -20 -25 -30 2110 2130 2150 Frequency (MHz) P1dB vs. Frequency -40C +25C 20 2110 2130 2150 Frequency (MHz) OIP3 vs. Temperature freq = 2140, 2141 MHz ...
Page 9
... The active-bias circuit, shown on the right, uses dual PNP transistors to provide a constant drain current into the FP1189, while also eliminating the effects of pinchoff variation. This configuration is best suited for applications where the intended output power level of the amplifier is backed off at least 6 dB away from its compression point ...
Page 10
... DataSheet U .com The Communications Edge Product Marking The component will be marked with an “FP1189” designator with a four- or five-digit alphanumeric lot code on the top surface of the package. Tape and reel specifications for this part is located on the website in the “Application Notes” section. ...