IR3Y30M1 Sharp Electrionic Components, IR3Y30M1 Datasheet
IR3Y30M1
Available stocks
Related parts for IR3Y30M1
IR3Y30M1 Summary of contents
Page 1
... Built-in low-pass filter • Built-in comparator for electronic exposure control • Built-in aperture circuit and delay line • Single +5 V power supply • Packages – IR3Y30M : 48-pin QFP (QFP048-P-1010) – IR3Y30M1 : 48-pin QFP (QFP048-P-0707) 0.5 mm pin-pitch COMPARISON TABLE Package Power consumption P ...
Page 2
PIN CONNECTIONS 48-PIN QFP CCD IN CLAMP BIAS IRIS GAMMA WINDOW IRIS OUT V GND EE NR SET NR IRIS IN SET ...
Page 3
BLOCK DIAGRAM 3 IR3Y30M/M1 ...
Page 4
PIN DESCRIPTION PIN NO. PIN NAME VOLTAGE 2 CCDIN CLAMP 2 BIAS IRIS 3 GAMMA 4 WINDOW 2 IRIS OUT EQUIVALENT CIRCUIT V CC1 200 ...
Page 5
PIN NO. PIN NAME VOLTAGE 6 V CC1 7 GND SET NR 10 IRIS IN 11 SET SYNC EQUIVALENT CIRCUIT V CC1 50 k 200 8 8 GND V CC1 ...
Page 6
PIN NO. PIN NAME VOLTAGE BLK CLP 14 BCLIP CC2 VIDEO OUT 1 PEDESTAL 2 EQUIVALENT CIRCUIT V CC1 40 µ µ GND V CC1 40 µ ...
Page 7
PIN NO. PIN NAME VOLTAGE V WCLIP 3 CLAMP 2 AMP OUT 1 GAIN 2 CTRL C 1 EQUIVALENT CIRCUIT CC2 ...
Page 8
PIN NO. PIN NAME VOLTAGE C 1 APA CTRL 1 HAPA ADJ 1 GAMMA 2 OUT EQUIVALENT CIRCUIT V CC1 µ µ 200 ...
Page 9
PIN NO. PIN NAME VOLTAGE KNEE ADJ 2 GAMMA 2 ADJ GND 31 2 AGC DET 2 2 AMP EQUIVALENT CIRCUIT V CC1 ...
Page 10
PIN NO. PIN NAME VOLTAGE LPF ADJ 35 AGC OUT 2 2 REF V 2 AGC CTRL 39 EQUIVALENT CIRCUIT V CC1 200 35 GND V ...
Page 11
PIN NO. PIN NAME VOLTAGE AGC OP 40 OUT MAX 3 GAIN AGC CLAMP 2 CDS OUT 2 EQUIVALENT CIRCUIT V CC1 200 40 GND V CC1 ...
Page 12
PIN NO. PIN NAME VOLTAGE FCDS 47 PGND 48 EQUIVALENT CIRCUIT PV CC 100 µ 200 46 PGND PV CC 200 µ 200 47 PGND 12 IR3Y30M/M1 DESCRIPTION Power supply for pulse circuits. Pulse input ...
Page 13
FUNCTIONAL OPERATION CDS Circuit The feed-through level of the input signal is clamped by the clamp circuit. Then the signal period is sampled and other periods are held by the sample and hold circuit, so that signals can be obtained. ...
Page 14
... CC CC1 CC2 V Pin 26 (HAPA IN) H-AP V Pin 1 (CCD IN) CCD t Pin 46 (FS Pin 47 (FCDS) FCDS 14 IR3Y30M/M1 (Unless otherwise specified +25 ˚C) A RATING IR3Y30M IR3Y30M1 –0 0 725 560 5.8 4.5 –30 to +75 –30 to +70 –55 to +150 RATING ) 4.75 to 5.25 CC 600 (MAX.) 200 (TYP.) 15 (MIN ...
Page 15
ELECTRICAL CHARACTERISTICS (Unless otherwise specified +25 ˚ R27 = 30 k$, R35 = 22 k$) PARAMETER SYMBOL I Measure pin 6 (V CC1 Supply current I Measure pin 16 (V CC2 I Measure pin 45 (PV ...
Page 16
PARAMETER SYMBOL AGC circuit (contd.) AGC maximum gain Apply signal 3 to SG43 and G AMAX1 (1) measure the amplitude on AGC maximum gain TP36. G AMAX2 (2) GA1 to GA4 = 20*LOG (TP36 amplitude/SG43 AGC minimum gain G AMIN ...
Page 17
PARAMETER SYMBOL Exposure Circuit Apply signal 3 to SG43 and Exposure AMP gain G I measure the amplitude on Gamma output level ‹ TP5. PRE Output dynamic SW3, SW4, SW43/(b range Pulse/CLP, BLK Measure the voltage on TP5. ...
Page 18
PARAMETER SYMBOL Gamma & Knee Circuits (contd.) Apply signal 3 to SG34 and measure the amplitude on TP28. SW29, SW30, SW34/(b), Gamma OFF gain G ‹OFF Pulse/CLP, BLK, SG34 = 100 mVp-p, Black level = (1) C ...
Page 19
PARAMETER SYMBOL Encoder Circuit White clip (1) W Apply signal 3 to SG20 and C1 White clip (2) W measure the amplitude on C2 TP17A. White clip preset W CPRE SW20/(b), Pulse/CLP, BLK Measure the amplitude of Setup (1) S ...
Page 20
Measurement Waveforms Signal 1 Signal 2 (Input) T/2 (FCDS) T/4 T/4 (FS 1/f BLK 11 µs Blanking Pulse CLP 3 µs Clamp Pulse SYNC 4.7 µs Sync Pulse WINDOW Window pulse Signal 3 Signal 4 Sine wave amplitude ...
Page 21
Test Circuit R35 TP36 36 35 TP37A 37 0.01 µF TP37B TP40A TP40B 0.01 µF SG43 44 TP44 0.01 µ µF 100 $ 46 ...
Page 22
PACKAGES 48 QFP (QFP048-P-1010) 0. QFP (QFP048-P-0707) PACKAGES FOR CCD AND CMOS DEVICES TYP. 0.33 ±0 (1.75) (1.75) 0.85 10.0 ±0.2 ±0.4 1.45 13.5 TYP. ±0.08 0.5 0 ...