LTC2205 Linear Technology, LTC2205 Datasheet - Page 21

• Manufacturer Part Number: LTC2205
• Description: (LTC2204 / LTC2205) 65Msps/40Msps
• Manufacturer: Linear Technology

www.datasheet4u.com
APPLICATIONS INFORMATION
SAMPLE/HOLD OPERATION AND INPUT DRIVE
Sample/Hold Operation
Figure 2 shows an equivalent circuit for the LTC2205/
LTC2204 CMOS differential sample and hold. The differ-
ential analog inputs are sampled directly onto sampling
capacitors (C
capacitors shown attached to each input (C
the summation of all other capacitance associated with
each input.
During the sample phase when ENC is low, the NMOS
transistors connect the analog inputs to the sampling
capacitors which charge to, and track the differential in-
put voltage. When ENC transitions from low to high, the
sampled input voltage is held on the sampling capacitors.
During the hold phase when ENC is high, the sampling
capacitors are disconnected from the input and the held
voltage is passed to the ADC core for processing. As ENC
transitions for high to low, the inputs are reconnected to
the sampling capacitors to acquire a new sample. Since
the sampling capacitors still hold the previous sample,
a charging glitch proportional to the change in voltage
between samples will be seen at this time. If the change
between the last sample and the new sample is small,
the charging glitch seen at the input will be small. If the
input change is large, such as the change seen with input
frequencies near Nyquist, then a larger charging glitch
will be seen.
Common Mode Bias
The ADC sample-and-hold circuit requires differential
drive to achieve specifi ed performance. Each input should
swing ±0.5625V for the 2.25V range (PGA = 0) or ±0.375V
for the 1.5V range (PGA = 1), around a common mode
voltage of 1.25V. The V
to provide the common mode bias level. V
directly to the center tap of a transformer to set the DC
input level or as a reference level to an op amp differential
driver circuit. The V
close to the ADC with 2.2µF or greater.
SAMPLE
CM
) through NMOS transistors. The
CM
pin must be bypassed to ground
output pin (Pin 2) is designed
CM
PARASITIC
can be tied
) are
Input Drive Impedance
As with all high performance, high speed ADCs the
dynamic performance of the LTC2205/LTC2204 can be
infl uenced by the input drive circuitry, particularly the
second and third harmonics. Source impedance and in-
put reactance can infl uence SFDR. At the falling edge of
ENC the sample-and-hold circuit will connect the 4.9pF
sampling capacitor to the input pin and start the sampling
period. The sampling period ends when ENC rises, hold-
ing the sampled input on the sampling capacitor. Ideally,
the input circuitry should be fast enough to fully charge
the sampling capacitor during the sampling period
1/(2F
incomplete settling may degrade the SFDR. The sampling
glitch has been designed to be as linear as possible to
minimize the effects of incomplete settling.
For the best performance it is recommended to have a
source impedance of 100Ω or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
INPUT DRIVE CIRCUITS
Input Filtering
A fi rst order RC lowpass fi lter at the input of the ADC
can serve two functions: limit the noise from input cir-
cuitry and provide isolation from ADC S/H switching. The
LTC2205/LTC2204 have a very broadband S/H circuit, DC
to 700MHz; it can be used in a wide range of applications;
therefore, it is not possible to provide a single recom-
mended RC fi lter.
Figures 3, 4a and 4b show three examples of input RC
fi ltering at three ranges of input frequencies. In general
it is desirable to make the capacitors as large as can be
tolerated—this will help suppress random noise as well
as noise coupled from the digital circuitry. The LTC2205/
LTC2204 do not require any input fi lter to achieve data sheet
specifi cations; however, no fi ltering will put more stringent
noise requirements on the input drive circuitry.
ENCODE
); however, this is not always possible and the
LTC2205/LTC2204
21
22054fb