b210lp System Sensor, b210lp Datasheet

b210lp

Manufacturer Part Number

b210lp

Description

Low-profile Intelligent Combination Smoke Detector

Manufacturer

System Sensor

Datasheet

1.B210LP.pdf (2 pages)

Current page: 1 of 2
Download datasheet (495Kb)

INSTALLATION AND MAINTENANCE INSTRUCTIONS

B210LP Plug-in Detector Base

SPECIfICATIONS

Diameter:

Mounting:

Operating Temperature Range:

BEfORE INSTALLINg

Please thoroughly read the system wiring and installation manuals, and man-

ual System Smoke Detectors Application Guide, which provides detailed in-

formation on detector spacing, placement, zoning, and special applications.

Copies of these manuals are available from System Sensor or through a Sys-

tem Sensor distributor.

gENERAL DESCRIPTION

The B210LP is a plug in detector base intended for use in a 2-wire intelligent sys-

tem, with screw terminals provided for power (+ and –), and remote annuncia-

tor connections. Communication takes place over the power (+ and –) lines.

BASE TERMINALS

NO.

MOUNTINg

This detector base mounts directly to 3

square boxes (with or without plaster rings) and single gang boxes. To mount,

remove the decorative ring by turning it in either direction to unhook the

snaps, then separate the ring from the base. Install the base on the box using

the screws supplied with the junction box and the appropriate mounting slots

in the base.

Place the decorative ring on the base and rotate it in either direction until it

snaps into place (see Figure 2).

INSTALLATION WIRINg gUIDELINES

All wiring must be installed in compliance with all applicable local codes

and any special requirements of the authority having jurisdiction, using the

proper wire size. The conductors used to connect smoke detectors to control

panels and accessory devices should be color-coded to reduce the likelihood

of wiring errors. Improper connections can prevent a system from responding

properly in the event of a fire.

For signal wiring (the wiring between interconnected detectors), it is recom-

mended that the wire be no smaller than AWG 18. However, the screws and

clamping plate in the base can accommodate wire sizes up to AWG 12. The

use of twisted pair wiring or shielded cable for the power (+ and -) loop is

recommended to minimize the effects of electrical interference.

If shielded cable is used, the shield connection to and from the detector must

be continuous by using wire nuts, crimping, or soldering, as appropriate for a

reliable connection.

Make electrical connections by stripping about

from the end of the wire (use strip gauge molded in base), sliding the bare end

of the wire under the clamping plate, and tightening the clamping plate screw.

Do not loop the wire under the clamping plate.

The zone wiring of the detector base should be checked before the detector

heads are installed in them. The wiring should be checked for continuity and

polarity in the base, and dielectric tests should be performed.

The base includes a label for recording the zone, address, and type of detector

being installed. This information is important to set the address of the detector

head that will later be plugged into the base and to verify the type required

for that location.

D250-01-00

FUNCTION

Power (–), Remote Annunciator (–)

Power (+)

Remote Annunciator (+)

6.1 inches (155 mm)

4-inch (102 mm) square box with or without plaster ring; Minimum Depth - 1.5 inches (38 mm)

4-inch Octagon Box; Minimum Depth - 1.5 inches (38 mm)

Single Gang Box; Minimum Depth - 1.5 inches (38 mm)

Refer to applicable sensor Operating Temperature Range

using the Base/Sensor Cross Reference Chart at http:\\www.systemsensor.com

- and 4-inch octagon boxes, 4-inch

-inch Octagon Box; Minimum Depth - 1.5 inches (38 mm)

inch (10 mm) of insulation

fIgURE 1. TERMINAL LAyOUT:

fIgURE 2. MOUNTINg DETECTOR TO BOx:

TERMINALS

BASE

3825 Ohio Avenue, St. Charles, Illinois 60174

1-800-SENSOR2, FAX: 630-377-6495

TAMPER PROOF

TAB

www.systemsensor.com

SNAP ON

DECORATIVE

RING

SCREWS

(NOT SUPPLIED)

DETECTOR

BASE

BOX

(NOT SUPPLIED)

I56-0595-007R

C0127-00

C0128-00

Related parts for b210lp

b210lp Summary of contents

Page 1

... Sensor distributor. gENERAL DESCRIPTION The B210LP is a plug in detector base intended for use in a 2-wire intelligent sys- tem, with screw terminals provided for power (+ and –), and remote annuncia- tor connections. Communication takes place over the power (+ and –) lines. ...

Page 2

... RA400Z. See Figure 5 for installation. Please refer to insert for the Limitations of Fire Alarm Systems System Sensor warrants its enclosed smoke detector base to be free from defects in ma- terials and workmanship under normal use and service for a period of three years from date of manufacture ...

Related keywords

b210lp datasheet
b210lp data sheet
b210lp pdf datasheet
b210lp component
b210lp part
b210lp distributor
b210lp RoHS
b210lp datasheet download