eps40-1 System Sensor, eps40-1 Datasheet
eps40-1
Manufacturer Part Number
eps40-1
Description
Supervisory Pressure Switches
Manufacturer
System Sensor
Datasheet
1.EPS40-1.pdf
(2 pages)
EPS40-1 AND EPS40-2
Supervisory Pressure
Switches
System Sensor EPS40 Series switches are designed for
use in dry pipe systems or pressure tanks and water
pressure supplies of automatic water control valves.
Features
•
•
•
•
Agency Listings
Specifications, EPS40-1 and EPS40-2
Architectural/Engineering Specifi cations EPS40-1 (SPDT), EPS40-2 (2/SPDT)
Model shall be an EPS40-1 or EPS40-2 pressure type waterfl ow switch as manufactured by System Sensor of St. Charles, IL. They shall be installed on the sprinkler
system with connection as shown on the drawings and/or as specifi ed herein. Pressure switches shall be of the bellows-activated type. Switches shall have
a maximum service pressure rating of 250 psi and shall be adjustable from 10 – 100 psi. There shall be one (1) or two (2) SPDT contacts rated at 10.0 Amp @
125/250 VAC and 2.5 Amp @ 6/12/24 VDC. The contractor shall furnish and install, where indicated on the plans, pressure switches according to appropriate
NFPA standards. Switches shall be provided with a ½˝ NPT male pressure connection to be connected into the air supply line on the system side of any shut-off
valve. Switches shall provide 1 knockout type and 1 open hole for ½˝ conduit fi tting attachment and a ground screw provision for electrical grounding.
The switch enclosure shall be weatherproof and carry a UL 4x/NEMA 4 rating when used with proper electrical fi ttings and conduit. The cover shall incorporate
tamper-resistant screws. The unit shall be listed by Underwriters Laboratories, Inc., the California State Fire Marshal, MEA, CSFM, LPCB, VdS and approved by
Factory Mutual.
Sensitivity adjustment wheel, no special tools required
Reinforced diaphragm resists pressure spikes
Two conduit entrances
Both one- and two-switch models available
S739
VdS
G4020028
118f/01
7770-1209:147
0X0A7.AY
167-93-E
CS169
The EPS40-1 has a single SPDT switch while the EPS40-2 model
contains two SPDT switches. The EPS40 Series features fi eld
adjustable pressure sensitivity to provide an alarm response between
10 and 100 psi. All models are factory set for use in a nominal 40 psi
system. The EPS40-1 is factory set to respond at 30 psi at decreasing
pressure while the EPS40-2 is factory set to respond at 50 psi on
rising pressure and 30 psi at decreasing pressure. The pressure
adjustment wheel requires no special tools and does not aff ect
switch synchronization on the EPS40-2. The EPS40-1 and EPS40-2
supervisory pressure switches are NEMA 4 rated.
Related parts for eps40-1
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
2251br Intelligent Photoelectric Smoke Sensor With Remote Test Capability In Duct Applications
Manufacturer:
System Sensor
Datasheet:
Part Number:
Description:
SENSOR ABS PRESS 56.6 PSI MAX
Manufacturer:
Freescale Semiconductor
Datasheet:
Part Number:
Description:
SYSTEM SENSOR, ACCLIMATE
Manufacturer:
Freescale Semiconductor
Part Number:
Description:
400 Series Plug-in Smoke Detectors
Manufacturer:
System Sensor
Datasheet:
Part Number:
Description:
M500x Fault Isolator Module
Manufacturer:
System Sensor
Datasheet:
Part Number:
Description:
Signaling Strobe Sounder
Manufacturer:
System Sensor
Datasheet:
Part Number:
Description:
Duct Smoke Detector
Manufacturer:
System Sensor
Datasheet:
Part Number:
Description:
Low-profile Intelligent Combination Smoke Detector
Manufacturer:
System Sensor
Datasheet:
Part Number:
Description:
Low-profile Plug-in Smoke Detector
Manufacturer:
System Sensor
Datasheet:
Part Number:
Description:
System Voltage Regulator With Keep-alive On/off
Manufacturer:
National Semiconductor Corporation
Datasheet:
Part Number:
Description:
Carbon Monoxide Detector With Realtest™ Technology
Manufacturer:
System Sensor
Datasheet:
eps40-1 Summary of contents
Page 1
... Architectural/Engineering Specifi cations EPS40-1 (SPDT), EPS40-2 (2/SPDT) Model shall be an EPS40-1 or EPS40-2 pressure type waterfl ow switch as manufactured by System Sensor of St. Charles, IL. They shall be installed on the sprinkler system with connection as shown on the drawings and/or as specifi ed herein. Pressure switches shall be of the bellows-activated type. Switches shall have a maximum service pressure rating of 250 psi and shall be adjustable from 10 – ...
Page 2
... Pressure Range Diff erential Approximately 3 psi @ 10 psi, 6 psi @ 100 psi Factory Setting EPS40-1 operates at decreasing pressure at 30 psi EPS40-2 operates at increasing pressure at 50 psi and decreasing pressure at 30 psi Switch Contact Ratings EPS10-1: One set SPDT (Form C) EPS10-2: Two sets SPDT (Form C) 10.0 A, ½ ...