ta8260ah TOSHIBA Semiconductor CORPORATION, ta8260ah Datasheet
ta8260ah
Available stocks
Related parts for ta8260ah
ta8260ah Summary of contents
Page 1
... TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic Max Power 40 W BTL × 4CH Audio Power IC The TA8260AH BTL audio power amplifier for car audio application. This IC can generate more high power: P included the pure complementary PNP and NPN transistor output stage. ...
Page 2
... Block Diagram 2 TA8260AH 2002-03-05 ...
Page 3
... The voltage gain of Amp. 2A, B The voltage gain of BLT Connection : G Therefore, the total voltage gain is decided by expression below (BTL) (description is made only on the single channel) Figure 1 Block diagram : G = 0dB 20dB V2 = 6dB V (BTL 26dB 3 TA8260AH 2002-03-05 ...
Page 4
... ON or OFF by the microcomputer, the switching relay can be CC omitted. (2) Since the control current is microscopic, the switching relay of small current capacity is satisfactory for switching BE (SB) V (V) (SB) 0~1.5 3~6 Figure 2 With pin 2 set to high, power is turned ON Š Conventional method Š Š Stand-by switch method Š Figure 3 4 TA8260AH 2002-03-05 ...
Page 5
... BEEP sound or voice synthesizer signal can be input to pin 16 directly. and C and these parts is related the pop noise at power 1 4 must be set up less than 15 kº, we recommend 10 kº. Figure 5 Mute attenuationíV Figure 6 AUX input 5 TA8260AH _ 250 µA MUTE (V) mute 2002-03-05 ...
Page 6
... In unusual case that output terminal of Power Amp. is condition of output to V and over voltage input mode possible to protect all the system of apparatus as well as power IC protection. In case of being unused this function, use this IC as open-connection on pin 3. pin 3: Open collector output (active low) or output to GND short CC (Application) Figure 7 6 TA8260AH 2002-03-05 ...
Page 7
... It is possible to improve the audio quality with controlling the volume, tone control circuit through L.P.F. smoothing circuit as shown in Figure 8. In case of being unused this function, use this IC as open connection on pin 3. (Application) (A) Output (AC wave form) (B) Clip detector circuit (internal) (C) Clip DET. terminal (pin 3) (pin 3) pin 3: Open collector output (active low) Figure 8 Figure 9 7 TA8260AH 2002-03-05 ...
Page 8
... So we recommend to use by below method. OUT1, 2 L-ch (or R-ch) OUT3, 4 R-ch (or L-ch) And, please refer to below table in case of applying the AUX. IN because it is out to OUT1 and 4. ex) OUT1 Front OUT2 Rear OUT3 Rear OUT4 Front Figure 10 AUX. OUT L-ch (or R-ch) Š Š R-ch (or L-ch) AUX. OUT 8 TA8260AH 25°C 23 2002-03-05 ...
Page 9
... Stand-by condition H Š Power Š Power: off H Š Mute: off L Š Mute: on Mute: on 7.75 Vrms (20dBm) OUT Š at Mute: off. 9 TA8260AH Min Typ. Max Unit Š 200 400 mA Š 40 Š Š 37 Š W Š 27 Š Š Š ...
Page 10
... TA8260AH 2002-03-05 ...
Page 11
... TA8260AH 2002-03-05 ...
Page 12
... TA8260AH 2002-03-05 ...
Page 13
... Test Circuit 13 TA8260AH 2002-03-05 ...
Page 14
... Package Dimensions Weight: 9.8 g (typ.) 14 TA8260AH 2002-03-05 ...
Page 15
... TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. · The information contained herein is subject to change without notice. 15 TA8260AH 000707EBF 2002-03-05 ...