max5090aatet Maxim Integrated Products, Inc., max5090aatet Datasheet - Page 7

• Manufacturer Part Number: max5090aatet
• Description: Max5090, Max5090a, Max5090b, Max5090c 2a, 76v, High-efficiency Maxpower Step-down Dc-dc Converters
• Manufacturer: Maxim Integrated Products, Inc.

The MAX5090 step-down DC-DC converter operates
from a 6.5V to 76V input voltage range. A unique volt-
age-mode control scheme with voltage feed-forward
and an internal switching DMOS FET provides high effi-
ciency over a wide input voltage range. This pulse-
width-modulated converter operates at a fixed 127kHz
switching frequency or can be synchronized with an
external system clock frequency. The device also fea-
tures automatic pulse-skipping mode to provide high
efficiency at light loads. Under no load, the MAX5090
consumes only 310µA, and in shutdown mode, con-
sumes only 20µA. The MAX5090 also features under-
voltage-lockout, hiccup-mode output short-circuit
protection and thermal shutdown.
Use the ON/OFF function to program the external UVLO
threshold at the input. Connect a resistive voltage-
divider from V
ON/OFF, as shown in Figure 1. Calculate the threshold
value by using the following formula:
11, 15, 16
2A, 76V, High-Efficiency MAXPower Step-Down
13, 14
PIN
1, 2
10
12
—
3
4
5
6
7
8
9
ON/
OFF /Undervoltage Lockout (UVLO)
IN
ON/OFF
DRAIN
NAME
SGND
PGND
SYNC
N.C.
BST
V
_______________________________________________________________________________________
VD
LX
SS
FB
EP
to SGND with the center node to
IN
Detailed Description
Source Connection of Internal High-Side Switch
Boost Capacitor Connection. Connect a 0.22µF ceramic capacitor from BST to LX.
Input Voltage. Bypass V
Internal Regulator Output. Bypass VD to PGND with a 3.3µF/10V or greater ceramic capacitor.
Synchronization Input. Connect SYNC to an external clock for synchronization. Connect to SGND to
select the internal 127kHz switching frequency.
Soft-Start Capacitor Connection. Connect an external capacitor from SS to SGND to adjust the soft-
start time.
Output Sense Feedback Connection.
For fixed output voltage (MAX5090A/MAX5090B), connect FB to V
For adjustable output voltage (MAX5090C), use an external resistive voltage-divider to set V
regulating set point is 1.228V.
Shutdown Control Input. Pull ON/OFF low to put the device in shutdown mode. Drive ON/OFF high for
normal operation. Connect ON/OFF to V
Signal Ground. SGND must be connected to PGND for proper operation.
No Connection. Not internally connected.
Power Ground
Internal High-Side Switch Drain Connection
Exposed Pad. Solder EP to SGND plane to aid in heat dissipation. Do not use as the only electrical
ground connection.
IN
to SGND with a low-ESR capacitor as close to the device as possible.
Set the external V
maximum recommended value for R2 is less than 1MΩ.
ON/OFF is a logic input and can be safely driven to the
full V
startup. Drive ON/OFF to ground to shut down the
MAX5090. Shutdown forces the internal power MOSFET
off, turns off all internal circuitry, and reduces the V
supply current to 20µA (typ). The ON/OFF rising thresh-
old is 1.546V (max). Before any operation begins, the
voltage at ON/OFF must exceed 1.546V. The ON/OFF
input has 100mV hysteresis.
If the external UVLO threshold setting divider is not
used, an internal undervoltage-lockout feature monitors
the supply voltage at V
start when V
UVLO rising threshold is set at 6.17V with 0.5V hystere-
sis. The V
and 1.546V, respectively, for proper operation.
IN
with short leads for always-on operation.
IN
FUNCTION
range. Connect ON/OFF to V
IN
DC-DC Converters
V
and V
IN
UVLO TH
rises above 6.45V (max). The internal
(
UVLO(TH)
ON/OFF
)
=
OUT
IN



1
voltages must be above 6.5V
.
and allows the operation to
+
to greater than 6.45V. The
R
R
Pin Description
2
1



x
1 38
.
IN
for automatic
OUT
. V
FB
IN
7