max5351 Maxim Integrated Products, Inc., max5351 Datasheet
max5351
Available stocks
Related parts for max5351
max5351 Summary of contents
Page 1
... DIP pack- age. The MAX535 operates from a single +5V supply and the MAX5351 operates from a single +3.3V supply. Both devices draw only 280µA of supply current. The output amplifier’s inverting input is available to the user, allowing specific gain configurations, remote sensing, and high output current capability ...
Page 2
... Input Leakage Current I Input Capacitance C 2 _______________________________________________________________________________________ Operating Temperature Ranges + 0.3V) MAX535_C_A/MAX5351_C_A...............................0°C to +70°C DD MAX535_E_A/MAX5351_E_A ............................-40°C to +85°C MAX535BMJA/MAX5351BMJA .......................-55°C to +125°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10sec) .............................+300°C = 5kΩ 100pF MIN CONDITIONS ...
Page 3
Low-Power, 13-Bit Voltage-Output DACs ELECTRICAL CHARACTERISTICS: MAX535 (continued +5V ±10%, REF = 2.5V, GND = 0V +25°C. Output buffer connected in unity-gain configuration (Figure 8).) A PARAMETER SYMBOL DYNAMIC PERFORMANCE DIGITAL INPUTS Voltage Output ...
Page 4
... Low-Power, 13-Bit Voltage-Output DACs with Serial Interface ELECTRICAL CHARACTERISTICS: MAX5351 (V = +3.15V to +3.6V, REF = 1.25V, GND = 0V are +25°C. Output buffer connected in unity-gain configuration (Figure 8).) A PARAMETER SYMBOL STATIC PERFORMANCE—ANALOG SECTION Resolution N Integral Nonlinearity INL (Note 4) Differential Nonlinearity DNL Offset Error ...
Page 5
... Low-Power, 13-Bit Voltage-Output DACs ELECTRICAL CHARACTERISTICS: MAX5351 (continued +3.15V to +3.6V, REF = 1.25V, GND = 0V are +25°C. Output buffer connected in unity-gain configuration (Figure 8).) A PARAMETER SYMBOL TIMING CHARACTERISTICS SCLK Clock Period SCLK Pulse Width High SCLK Pulse Width Low CS Fall to SCLK Rise Setup Time ...
Page 6
Low-Power, 13-Bit Voltage-Output DACs with Serial Interface __________________________________________Typical Operating Characteristics (MAX535 only +5V 5kΩ INTEGRAL NONLINEARITY vs. REFERENCE VOLTAGE 0.3 0.2 0.1 0 -0.1 -0.2 -0.3 -0.4 -0.5 0.4 0.8 1.2 1.6 ...
Page 7
Low-Power, 13-Bit Voltage-Output DACs ____________________________Typical Operating Characteristics (continued) (MAX535 only +5V 5kΩ MAJOR-CARRY TRANSITION CS 5V/div OUT, AC COUPLED 100mV/div 10 s/div _______________________________________________________________________________________ with Serial Interface = 100pF +25°C, unless otherwise ...
Page 8
... Low-Power, 13-Bit Voltage-Output DACs with Serial Interface ____________________________Typical Operating Characteristics (continued) (MAX5351 only +3.3V 5kΩ INTEGRAL NONLINEARITY vs. REFERENCE VOLTAGE 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 0.4 0.8 1.2 1.6 2.0 2.4 REFERENCE VOLTAGE (V) POWER-DOWN SUPPLY CURRENT vs. TEMPERATURE 5.0 4.5 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -60 - 100 140 TEMPERATURE (°C) OUTPUT FFT PLOT 1.9Vp-p REF CODE = FULL SCALE ...
Page 9
... Applications Information section). With a full-scale transition at the MAX535/MAX5351 out- put, the typical settling time to ±1/2LSB is 16µs when loaded with 5kΩ in parallel with 100pF (loads less than 2kΩ degrade performance). ...
Page 10
... The serial interface remains active. Data in the input registers is retained in shutdown, allowing the MAX535/MAX5351 to recall the output state prior to entering shutdown. Exit shutdown mode by either recall- ing the previous configuration or by updating the DAC with new data. When powering up the device or bringing it out of shutdown, allow 20µ ...
Page 11
Low-Power, 13-Bit Voltage-Output DACs Table 1. Serial-Interface Programming Commands 16-BIT SERIAL WORD D12............................ MSB bits of data bits of data XXXXXXXXXXXXX XXXXXXXXXXXXX 0 ...
Page 12
... CS MAX535 MAX5351 SCLK DIN Figure 7. Multiple MAX535/MAX5351s Sharing Common DIN and SCLK Lines Figure 7 shows a method of connecting several MAX535/MAX5351s. In this configuration, the clock and the data bus are common to all devices and separate chip-select lines are used for each IC. __________Applications Information For a unipolar output, the output voltage and the refer- ence input have the same polarity ...
Page 13
... The MAX535’s total harmonic distortion plus noise (THD + N) is typically less than -77dB (full-scale code), and the MAX5351’s THD + N is typically less than -72dB (full-scale code), given a 1Vp-p signal swing and input frequencies up to 25kHz. The typical -3dB frequency is ...
Page 14
... GND Figure 12. Digitally Programmable Current Source Power-Supply Considerations On power-up, the input and DAC registers are cleared (set to zero code). For rated MAX535/MAX5351 performance, REF should be at least 1.4V below V . Bypass V DD capacitor in parallel with a 0.1µF capacitor to GND. Use short lead lengths and place the bypass capaci- tors as close to the supply pins as possible ...
Page 15
... MAX5351BCUA 0°C to +70°C 8 µMAX MAX5351BC/D 0°C to +70°C Dice* MAX5351AEPA -40°C to +85°C 8 Plastic DIP MAX5351BEPA -40°C to +85°C 8 Plastic DIP MAX5351AEUA -40°C to +85°C 8 µMAX MAX5351BEUA -40°C to +85°C 8 µMAX MAX5351BMJA -55°C to +125°C 8 CERDIP** † ...
Page 16
Low-Power, 13-Bit Voltage-Output DACs with Serial Interface ___________________________________________Package Information (continued Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a ...