max5331ucb-td Maxim Integrated Products, Inc., max5331ucb-td Datasheet
max5331ucb-td
Related parts for max5331ucb-td
max5331ucb-td Summary of contents
Page 1
... No External Components Required for Setting Gain and Offset ♦ Integrated Output Clamp Diodes ♦ Three Output-Impedance Options MAX5331 (50Ω), MAX5332 (500Ω), and MAX5333 (1kΩ) PART MAX5331UCB MAX5331UTK* MAX5332UCB MAX5332UTK* MAX5333UCB MAX5333UTK* *Future product—contact factory for availability. TOP VIEW ...
Page 2
DACs with 32-Channel Sample-and-Hold Outputs ABSOLUTE MAXIMUM RATINGS V to AGND.......................................................-0.3V to +12. AGND .........................................................-6.0V to +0. ...........................................................................+15V AGND or DGND ..............-0.3V to +6V ...
Page 3
ELECTRICAL CHARACTERISTICS (continued +10V -4V LOGIC CLKSEL = +5V 400kHz ECLK A PARAMETER SYMBOL DYNAMIC CHARACTERISTICS Sample-and-Hold Settling SCLK Feedthrough f Feedthrough SEQ Hold Step Droop ...
Page 4
DACs with 32-Channel Sample-and-Hold Outputs ELECTRICAL CHARACTERISTICS (continued +10V -4V LOGIC LDAC CLKSEL = +5V 400kHz ECLK A MIN PARAMETER SYMBOL SCLK-High to CS-High Hold ...
Page 5
V = -4V +2.5V REF INTEGRAL NONLINEARITY vs. INPUT CODE 0.040 0.035 0.030 0.025 0.020 0.015 0.010 250 930 1610 2290 2970 INPUT CODE DIFFERENTIAL NONLINEARITY TEMPERATURE VS. 0.30 0.25 0.20 0.15 ...
Page 6
DACs with 32-Channel Sample-and-Hold Outputs (V = +10V -4V +2.5V REF LOGIC SUPPLY CURRENT vs. LOGIC SUPPLY VOLTAGE 900 800 700 600 500 INTERFACE INACTIVE 400 4.75 5.00 5.25 5.50 LOGIC SUPLY ...
Page 7
PIN TQFP THIN QFN 17, 34, 51 15, 25, 40, 55, ...
Page 8
DACs with 32-Channel Sample-and-Hold Outputs PIN TQFP THIN QFN ...
Page 9
CS t CSHO t t CSSO CH SCLK B23 DIN Figure 2. Serial-Interface Timing Diagram Detailed Description Sample-and-Hold Amplifiers The MAX5331/MAX5332/MAX5333 contain 32 buffered SHA circuits with internal hold capacitors. Internal hold capacitors minimize leakage current, ...
Page 10
DACs with 32-Channel Sample-and-Hold Outputs combinations of negative and positive power-supply voltages. The nominal, usable DAC end-point codes for the selected power supplies can be calculated as: Lower end-point code = 2048 - ((2. 3.2mV) (result ≥ ...
Page 11
Table 2. Channel/Output Selection ...
Page 12
DACs with 32-Channel Sample-and-Hold Outputs The operating modes can also be selected externally through CLKSEL and IMMED. If the control bit in the serial word and the external signal conflict, the signal that is a logic 1 is dominant. ...
Page 13
Burst mode allows multiple SRAM locations to be loaded at high speed. During burst mode, the output voltages are not updated until the data burst is com- plete and control returns to the sequencer. Select burst mode by driving both ...
Page 14
DACs with 32-Channel Sample-and-Hold Outputs +2.5V Figure 7. Typical Operating Circuit Pin Configurations (continued) TOP VIEW CL 52 OUT21 53 OUT22 54 OUT23 55 OUT24 56 OUT25 57 AGND 58 OUT26 59 MAX5331 OUT27 60 MAX5332 61 OUT28 MAX5333 ...
Page 15
For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ 12-Bit DACs with 32-Channel Sample-and-Hold Outputs PACKAGE OUTLINE, 64L TQFP, 10x10x1.4mm PACKAGE OUTLINE, 64L TQFP, 10x10x1.4mm ...
Page 16
... Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products Package Information (continued) Printed USA is a registered trademark of Maxim Integrated Products, Inc. PACKAGE OUTLINE 68L THIN QFN, 10x10x0.8mm 1 C 21-0142 ...