max5530etct Maxim Integrated Products, Inc., max5530etct Datasheet
max5530etct
Related parts for max5530etct
max5530etct Summary of contents
Page 1
Rev 0; 1/04 General Description The MAX5530/MAX5531 are single, 12-bit, ultra-low- power, voltage-output, digital-to-analog converters ® (DACs) offering Rail-to-Rail buffered voltage outputs. The DACs operate from a 1.8V to 5.5V supply and con- sume less than 6µA, making them ...
Page 2
Ultra-Low-Power, 12-Bit, Voltage-Output DACs ABSOLUTE MAXIMUM RATINGS V to GND ..............................................................-0.3V to +6V DD OUT to GND ...............................................-0. GND ..................................................-0. GND ..............................-0. SCLK, DIN, REFIN, REFOUT to GND ............................-0.3V to ...
Page 3
ELECTRICAL CHARACTERISTICS (continued +1.8V to +5.5V, OUT unloaded PARAMETER SYMBOL Power-Supply Rejection Ratio REFERENCE INPUT (MAX5530) Reference-Input Voltage Range V Reference-Input Impedance R REFERENCE OUTPUT (MAX5531) Initial Accuracy V Output-Voltage Temperature V Coefficient Line Regulation Load ...
Page 4
Ultra-Low-Power, 12-Bit, Voltage-Output DACs ELECTRICAL CHARACTERISTICS (continued +1.8V to +5.5V, OUT unloaded PARAMETER SYMBOL DAC Power-Up Time Output Power-Up Glitch FB_ Input Current DIGITAL INPUTS (SCLK, DIN, CS) Input High Voltage V Input Low Voltage Input ...
Page 5
TIMING CHARACTERISTICS (V = +4.5V to +5.5V MIN MAX PARAMETER SYMBOL TIMING CHARACTERISTICS (V = 4.5V TO 5.5V) DD Serial Clock Frequency DIN to SCLK Rise Setup Time DIN to SCLK Rise Hold ...
Page 6
Ultra-Low-Power, 12-Bit, Voltage-Output DACs (V = 5.0V 4.096V (MAX5530), V REF DD SUPPLY CURRENT vs. SUPPLY VOLTAGE (MAX5531 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 ...
Page 7
V = 4.096V (MAX5530 REF DNL vs. INPUT CODE ( 5V) DD REF 0.20 0.15 0.10 0.05 0 -0.05 -0.10 -0.15 0 500 1000 1500 2000 2500 3000 3500 4000 4500 DIGITAL ...
Page 8
Ultra-Low-Power, 12-Bit, Voltage-Output DACs (V = 5.0V 4.096V (MAX5530), V REF DD OUTPUT LARGE-SIGNAL STEP RESPONSE ( 3.9V) DD REF MAX5530 toc19 V OUT 500mV/div 200µs/div MAJOR CARRY OUTPUT VOLTAGE GLITCH (CODE 7FFh TO ...
Page 9
V = 4.096V (MAX5530 REF REFERENCE LINE-TRANSIENT RESPONSE (V = 1.2V) REF 100µs/div REFERENCE LOAD TRANSIENT (V = 1.8V) DD 200µs/div REFERENCE LOAD TRANSIENT (V = 1.8V) DD 200µs/div _______________________________________________________________________________________ Ultra-Low-Power, 12-Bit, Voltage-Output DACs Typical ...
Page 10
Ultra-Low-Power, 12-Bit, Voltage-Output DACs (V = 5.0V 4.096V (MAX5530), V REF DD REFERENCE PSRR vs. FREQUENCY 1. 0.01 0.1 FREQUENCY (kHz) REFERENCE OUTPUT NOISE (0.1Hz TO ...
Page 11
PIN NAME MAX5530 MAX5531 SCLK 3 3 DIN 4 — REFIN — 4 REFOUT N. GND 10 10 OUT 12 12 ...
Page 12
Ultra-Low-Power, 12-Bit, Voltage-Output DACs POWER- DOWN CONTROL CONTROL SCLK LOGIC DIN AND SHIFT CS REGISTER Detailed Description The MAX5530/MAX5531 single, 12-bit, ultra-low-power, voltage-output DACs offer Rail-to-Rail buffered voltage outputs. The DACs operate from a 1.8V to 5.5V supply and require ...
Page 13
Table 1. Serial Write Data Format CONTROL MSB D11 SCLK DIN CS t CSW Figure 1. Timing Diagram SCLK DIN CONTROL BITS CS Figure 2. Register Loading Diagram ______________________________________________________________________________________ Ultra-Low-Power, ...
Page 14
Ultra-Low-Power, 12-Bit, Voltage-Output DACs Table 2. Serial-Interface Programming Commands CONTROL BITS ...
Page 15
The MAX5530/MAX5531 feature two power modes to conserve power during idle periods. In normal opera- tion, the device is fully operational. In shutdown mode, the device is completely powered down, including the internal voltage reference in the MAX5531. The MAX5531 ...
Page 16
Ultra-Low-Power, 12-Bit, Voltage-Output DACs Applications Information 1-Cell and 2-Cell Circuit See Figure 3 for an illustration of how to power the MAX5530/MAX5531 with either one lithium-ion battery or two alkaline batteries. The low current consumption of the devices makes the ...
Page 17
REFIN DAC MAX5530 V × N REFIN DAC I = LED 4096 × THE NUMERIC VALUE OF THE DAC INPUT CODE. DAC Figure 4. Programmable Current Source Driving an LED DAC REFIN MAX5530 FB I TRANSDUCER T ...
Page 18
Ultra-Low-Power, 12-Bit, Voltage-Output DACs Power Supply and Bypassing Bypass the power supply with a 0.1µF capacitor to GND. Minimize lengths to reduce lead inductance. If noise becomes an issue, use shielding and/or ferrite beads to increase isolation. For the thin ...
Page 19
For the latest package outline information www.maxim-ic.com/packages Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim ...