max5821 Maxim Integrated Products, Inc., max5821 Datasheet
max5821
Available stocks
Related parts for max5821
max5821 Summary of contents
Page 1
... The device operates from a single 2.7V to 5.5V supply 115µ 3.6V. A power-down mode decreases DD current consumption to less than 1µA. The MAX5821 fea- tures three software-selectable power-down output impedances: 100kΩ, 1kΩ, and high impedance. Other features include internal precision rail-to-rail output buffers and a power-on reset (POR) circuit that powers up the DAC in the 100kΩ ...
Page 2
Dual, 10-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC ABSOLUTE MAXIMUM RATINGS V , SCL, SDA to GND ............................................-0.3V to +6V DD OUT_, REF, ADD to GND..............................-0. Maximum Current into Any Pin............................................50mA Continuous Power Dissipation (T = +70°C) A 8-Pin ...
Page 3
Dual, 10-Bit, Low-Power, 2-Wire, Serial ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.5V, GND = REF +5V +25°C.) (Note PARAMETER SYMBOL Input Hysteresis Input Leakage Current Input Capacitance DIGITAL ...
Page 4
Dual, 10-Bit, Low-Power, 2-Wire, Serial Voltage-Output DAC ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.5V, GND = REF +5V +25°C.) (Note PARAMETER SYMBOL STOP Condition Setup Time ...
Page 5
Dual, 10-Bit, Low-Power, 2-Wire, Serial (V = +5V +25°C ZERO-CODE ERROR vs. SUPPLY VOLTAGE LOAD 0 2.7 3.4 4.1 4.8 SUPPLY VOLTAGE (V) GAIN ERROR ...
Page 6
... CODE = 200 hex TO 1FF hex 2 s/div DIGITAL FEEDTHROUGH MAX5821 toc23 SCL 500mV/div OUT_ C = 200pF LOAD f = 12kHz SCL CODE = 000 hex 40 s/div EXITING SHUTDOWN MAX5821 toc18 5V 0 OUT_ 10mV/div C = 200pF LOAD CODE = 200 hex 2 s/div SETTLING TIME (POSITIVE) MAX5821 toc21 5mV/div OUT_ C ...
Page 7
... The MAX5821 is SMBus com- patible within the range of V SCL facilitate bidirectional communication between the MAX5821 and the master at rates up to 400kHz. Figure Output Buffer 1 shows the 2-wire interface timing diagram. The MAX5821 is a transmit/receive slave-only device, rely- ing upon a master to generate a clock signal ...
Page 8
... Such a change occurs when a command word is required to initiate a Bit Transfer read operation. S master is writing to several I want to relinquish control of the bus. The MAX5821 seri- al interface supports continuous write operations with or without an S read operations require S change in direction of data flow. ...
Page 9
... The LSB of the address word is the R/W indicates whether the master is writing to or read- ing from the MAX5821 (R selects the write condi- tion, R selects the read condition). After receiving the proper address, the MAX5821 issues an ACK by pulling SDA low for one clock cycle. ...
Page 10
... PD0 and PD1 (Table 1). Any combination of the DACs can be controlled with a single write sequence. In read mode (R/W = 1), the MAX5821 writes the con- tents of the DAC register to the bus. The direction of data flow reverses following the address acknowledge by the MAX5821 ...
Page 11
Dual, 10-Bit, Low-Power, 2-Wire, Serial Table 3. Command Byte Definitions SERIAL DATA INPUT DAC DATA DAC DATA DAC DATA DAC ...
Page 12
... LSB MSB R ACK = 0 DATA BYTES GENERATED BY MASTER DEVICE LSB MSB R ACK X X PD1 = 1 DATA BYTES GENERATED BY MAX5821 LSB ACK P REF 10-BIT MUX AND DAC DAC REGISTER A 10-BIT MUX AND DAC DAC REGISTER B POWER-DOWN CIRCUITRY V GND DD TRANSISTOR COUNT: 11,186 ...
Page 13
... Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © 2005 Maxim Integrated Products Voltage-Output DAC BOTTOM VIEW SIDE VIEW Printed USA is a registered trademark of Maxim Integrated Products, Inc. Package Information MILLIMETERS INCHES MAX MIN DIM MIN MAX - 0.043 - 1. ...