pi3usba03 Pericom Semiconductor Corporation, pi3usba03 Datasheet
pi3usba03
Related parts for pi3usba03
pi3usba03 Summary of contents
Page 1
... Each input/output has high integrated ESD 12kV HBM protection, per JESD22 specifi cation. This single chip solution integrates three ICs into a single easy to use solution. PI3USBA03 also offers PCB board savings with a total package size of 1.3mm x 2.8mm. Pin Description ...
Page 2
... DD ) ........................................ +150° PI3USBA03 Stresses greater than those listed under MAXIMUM Note: RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specifi cation is not implied. Ex- posure to absolute maximum rating conditions for extended periods may affect reliability ...
Page 3
... 2.7V to 3.6V DD (1) VIN = -0.4V, 1.0V (2) ION = -40mA ( 3. 25°C ambient and maximum loading. Test Conditions V = 2.7V to 3.6V @ 480mbps 2.7V to 3.6V @ 480 mbps 2. 2. PI3USBA03 (4) Min. Typ. Max. 1.3 0.6 1.0 0.15 5 0.12 0.15 1.4 0.5 1.0 , temperature, and voltage. DD Min. Typ. Max. -40 -38 1.1 360 PS8886B Units V μA Ω μA ...
Page 4
... For max. or min. conditions, use appropriate value specifi ed under Electrical Characteristics for the applicable device type. 3. Typical values are 3.3V 07-0239 3.3V, Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals Description Description 25C ambient and maximum loading. 4 PI3USBA03 Test Conditions Typ. Units 2 2.7V 2 5.0 (2) Test (3) Min. ...
Page 5
... Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals OUT D.U the Pulse Generator OUT Switch GND Open HP4396B PI3USBA03 HP11667A 5 PI3USBA03 200-ohm 10pF 200-ohm 50Ω, t ≤ 2.5ns, t ≤ 2.5ns 10pF PS8886B 10/30/07 ...
Page 6
... MAX GND 3. A_EN DD 6 1.25V 1.25V t PZL t PLZ Output V DD/2 t PZH t PHZ V DD/2 Output Min. Typ. Max -160 160 DD 1.3 0.6 200 -1 1 1.65 4.6 PI3USBA03 2. +0. –0. Units V Ω μA V PS8886B 10/30/07 ...
Page 7
... High Speed (480Mbs) Signals and Audio Signals Test Conditions = 5pF 50Ω MHz 5pF 50Ω MHz, L Test Conditions MHz, See Test Circuit Figure MHz, See Test Circuit Figure 8. 7 PI3USBA03 Min. Typ. Max. Units 2.7 pC ...
Page 8
... Switch 90% Output Logic Input Waveforms inverted for Switches that have opposite logic Figure 2. AC Waveforms OUT 50Ω 35pF Figure 3. Break Before Make Interval Timing 8 PI3USBA03 V OUT 35pF t < 5ns r t < 5ns f Off t OFF 90% 50% Logic ...
Page 9
... High Speed (480Mbs) Signals and Audio Signals Logic V OUT C L 1nF Figure 4. Charge Injection Test DD DD Signal Generator IH DD Capacitance DD Logic Input A_ENX 9 PI3USBA03 OFF ON Input Q = (ΔV )(C ) OUT 10nF A_ENX Analyzer GND ...
Page 10
... Introduction USB compliance test was done on the PI3USBA03 USB path. There are two main parts for the compliance test: TDR and Tektronics Signal Quality Test for both USB 2.0 High Speed and USB 2.0 Full Speed Specifi cation. Please refer to section 1 and 2. ...
Page 11
... Section 1: TDR Measurement for USB Signal Path 07-0239 3.3V, Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals Figure 1: TDRon the USB signal path PI3USBA03 =3.3V, 25C DD PS8886B 10/30/07 ...
Page 12
... Device ID: fsfe_001 Device Description: Full Speed, Far End Device, Down Stream Testing, Tier 6, Dummy Device. Date: Mon Feb 26 16:41:59 CST 2007 Overall Result: Pass* 07-0239 3.3V, Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals Figure 2. Waveform Plot 12 PI3USBA03 PS8886B 10/30/07 ...
Page 13
... Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals Figure 3. Eye Diagram 13 PI3USBA03 PS8886B 10/30/07 ...
Page 14
... Signal Quality Test Results in Tektronics format Device ID: fsfe_001 Device Description: High Speed, Near End Device, Up Stream Testing, Tier 1, Dummy Device. Date: Mon Feb 26 16:38:50 CST 2007 Overall Result: Pass* 07-0239 3.3V, Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals Figure 4. Waveform Plot 14 PI3USBA03 PS8886B 10/30/07 ...
Page 15
... Consecutive Jitter range : -65.36ps to 71.84ps, RMS Jitter 29.2ps KJ Paired Jitter range : -81.78ps to 80.23ps, RMS Jitter 32.6ps JK Paired Jitter range : -88.25ps to 78.97ps, RMS Jitter 30.3ps 07-0239 3.3V, Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals Figure 5. Eye Diagram 15 PI3USBA03 PS8886B 10/30/07 ...
Page 16
... E = Pb-free and Green • X suffi Tape/Reel Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com 07-0239 3.3V, Signal Switch Solution for USB 2.0 High Speed (480Mbs) Signals and Audio Signals Package Code Package Description ZN Pb-free & Green, 16-contact TQFN 16 PI3USBA03 Top Mark ME PS8886B 10/30/07 ...