lm4899 National Semiconductor Corporation, lm4899 Datasheet

no-image

lm4899

Manufacturer Part Number
lm4899
Description
1 Watt Fully Differential Audio Power Amplifier With Shutdown Select And Fixed 6db Gain
Manufacturer
National Semiconductor Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
lm4899ITL/NOPB
Manufacturer:
LITTELFUSE
Quantity:
23 100
Part Number:
lm4899LD
Manufacturer:
NS
Quantity:
82
Part Number:
lm4899LD
Manufacturer:
NS
Quantity:
86
Part Number:
lm4899LD
Manufacturer:
NS
Quantity:
86
Part Number:
lm4899LD
Manufacturer:
NSC
Quantity:
84
Part Number:
lm4899LD
Manufacturer:
NS/国半
Quantity:
20 000
© 2003 National Semiconductor Corporation
LM4899
1 Watt Fully Differential Audio Power Amplifier With
Shutdown Select and Fixed 6dB Gain
General Description
The LM4899 is a fully differential audio power amplifier
primarily designed for demanding applications in mobile
phones and other portable communication device applica-
tions. It is capable of delivering 1 watt of continuous average
power to an 8Ω load with less than 1% distortion (THD+N)
from a 5V
Boomer audio power amplifiers were designed specifically to
provide high quality output power with a minimal amount of
external components. The LM4899 does not require output
coupling capacitors or bootstrap capacitors, and therefore is
ideally suited for mobile phone and other low voltage appli-
cations where minimal power consumption is a primary re-
quirement.
The LM4899 features a low-power consumption shutdown
mode. To facilitate this, Shutdown may be enabled by either
logic high or low depending on mode selection. Driving the
shutdown mode pin either high or low enables the shutdown
select pin to be driven in a likewise manner to enable Shut-
down. Additionally, the LM4899 features an internal thermal
shutdown protection mechanism.
The LM4899 contains advanced pop & click circuitry which
virtually eliminates noises which would otherwise occur dur-
ing turn-on and turn-off transitions.
The LM4899 has an internally fixed gain of 6dB.
Connection Diagrams
Boomer
®
is a registered trademark of National Semiconductor Corporation.
Order Number LM4899ITL, LM4899ITLX
DC
See NS Package Number TLA09AAA
power supply.
9 Bump micro SMD Package
Top View
200645A0
DS200645
Key Specifications
Features
n Fully differential amplification
n Internal-gain-setting resistors
n Available in space-saving packages micro SMD, MSOP
n Ultra low current shutdown mode
n Can drive capacitive loads up to 500pF
n Improved pop & click circuitry which virtually eliminates
n 2.4 - 5.5V operation
n No output coupling capacitors, snubber networks or
n Shutdown high or low selectivity
Applications
n Mobile phones
n PDAs
n Portable electronic devices
j
j
j
j
and LLP
noises during turn-on and turn-off transitions
bootstrap capacitors required
Improved PSRR at 217Hz
Power Output at 5.0V & 1% THD
Power Output at 3.3V & 1% THD
Shutdown Current
9 Bump micro SMD Marking
T - Die Run Traceability
G - Boomer Family
C1 - LM4899ITL
X - Date Code
200645C7
400mW(typ.)
www.national.com
0.1µA(typ.)
1.0W(typ.)
July 2003
83dB

Related parts for lm4899

lm4899 Summary of contents

Page 1

... The LM4899 contains advanced pop & click circuitry which virtually eliminates noises which would otherwise occur dur- ing turn-on and turn-off transitions. The LM4899 has an internally fixed gain of 6dB. Connection Diagrams 9 Bump micro SMD Package 200645A0 Top View ...

Page 2

... See NS Package Number MUB10A LD Package Top View Order Number LM4899LD See NS Package Number LDA10B www.national.com (Continued) 20064523 20064535 2 MSOP Marking 200645C9 Z - Assembly Code X - Date Code TT - Die Run Traceability G - Boomer Family B1 - LM4899MM LD Marking 200645C8 Z - Assembly Code XY - Date Code TT - Die Run Traceability L4899 - LM4899LD ...

Page 3

Typical Application FIGURE 1. Typical Audio Amplifier Application Circuit 3 200645D0 www.national.com ...

Page 4

... Conditions V = 0V, no Load 0V 8Ω GND SDMODE SHUTDOWN THD = 1% (max kHz LM4899LD 4Ω (Note 11) L LM4899 8Ω 0.4 Wrms 1kHz 200mV sine p-p ripple f = 217Hz (Note 1kHz (Note 217Hz (Note 10 1kHz (Note 10) ...

Page 5

... Note 8: For micro SMD only, shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase I Note 9: Unterminated input. Note 10: 10Ω terminated input. Note 11: : When driving 4Ω loads from a 5V power supply, the LM4899LD must be mounted to a circuit board with the exposed-DAP area soldered down to a 1sq. in plane of 1oz. copper. External Components Description Components 1 ...

Page 6

... Typical Performance Characteristics LD Specific Characteristics THD+N vs Output Power 4Ω LM4899LD Power Dissipation vs Output Power www.national.com THD+N vs Frequency 200645C1 Power Derating Curve 20064511 6 = 4Ω 200645B5 LM4899LD 20064512 ...

Page 7

Typical Performance Characteristics Non-LD Specific Characteristics THD+N vs Frequency 8Ω 400mW THD+N vs Frequency 4Ω 225mW THD+N vs Frequency V ...

Page 8

Typical Performance Characteristics Non-LD Specific Characteristics THD+N vs Output Power 8Ω THD+N vs Output Power V = 2.6V PSRR vs Frequency 8Ω, Input 10Ω Terminated ...

Page 9

Typical Performance Characteristics Non-LD Specific Characteristics Output Power vs Supply Voltage R = 8Ω L Power Dissipation vs Output Power Power Dissipation vs Output Power (Continued) Output Power vs Supply Voltage 200645A6 Power Dissipation vs 20064581 20064583 ...

Page 10

Typical Performance Characteristics Non-LD Specific Characteristics Supply Current vs Shutdown Voltage Shutdown Low Clipping (Dropout) Voltage vs Supply Voltage Power Derating Curve www.national.com (Continued) Supply Current vs Shutdown Voltage 20064585 Open Loop Frequency Response 20064587 20064589 10 Shutdown High 20064586 ...

Page 11

Typical Performance Characteristics Non-LD Specific Characteristics CMRR vs Frequency 8Ω, 200mV DD L PSRR vs Common Mode Voltage (Continued 200645A3 PSRR vs Common Mode Voltage V = 3V, R ...

Page 12

... The DD share the same PCB layer, a nominal 2.5in necessary for 5V operation with a 4Ω load. Heatsink areas not placed on the same PCB layer as the LM4899 should be 2 5in (min) for the same supply voltage and load resistance. The last two area recommendations apply for 25˚C ambient temperature. In all circumstances and conditions, the junc- tion temperature must be held below 150˚ ...

Page 13

... This allows the JA designer maximum flexibility in device use, as the Shutdown Mode pin may simply be tied permanently to either V GND to set the LM4899 as either a "shutdown-high" device , of the system "shutdown-low" device, respectively. The device may ...

Page 14

... Physical Dimensions unless otherwise noted X1 = 1.514 www.national.com inches (millimeters) 9-Bump micro SMD Order Number LM4899ITL NS Package Number TLA09AAA ± ± 0. 1.514 0. 0.600 14 ± 0.075 ...

Page 15

... Physical Dimensions inches (millimeters) unless otherwise noted (Continued) LLP Order Number LM4899LD NSPackage Number LDA10B 15 www.national.com ...

Page 16

... National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. inches (millimeters) unless otherwise noted (Continued) Mini Small Outline (MSOP) Order Number LM4899MM NSPackage Number MUB10A 2. A critical component is any component of a life ...

Related keywords