lm26003mhx National Semiconductor Corporation, lm26003mhx Datasheet
lm26003mhx
Available stocks
Related parts for lm26003mhx
lm26003mhx Summary of contents
Page 1
... Other features include Power good, adjustable soft-start, en- able pin, input under-voltage protection, and an internal boot- strap diode for reduced component count. Typical Application Circuit © 2008 National Semiconductor Corporation Features ■ High efficiency sleep mode ■ 40 µA typical Iq in sleep mode ■ ...
Page 2
... Connection Diagram Ordering Information Order Number Package Type LM26003MH TSSOP-20EXP LM26003MHX Pin Descriptions Pin # Pin Name Description 1 VIN Power supply input for high side FET 2 VIN Power supply input for high side FET 3 VIN Power supply input for high side FET ...
Page 3
Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Voltages from the indicated pins to GND: VIN SW (Note 7) VDD VBIAS FB BOOT V PGOOD FREQ SYNC ...
Page 4
Symbol Parameter T Minimum Off-time OFFMIN T Minimum On-time ONMIN TH Sleep Mode Threshold Hysteresis SLEEP_HYS TH Wake Up Threshold WAKE I BOOT Pin Leakage Current BOOT Protection I Peak Current Limit LIMPK V Short Circuit Frequency Foldback FB_SC Threshold ...
Page 5
Typical Performance Characteristics 12V 25°C. J Efficiency vs Load Current (300 kHz) VFB vs Temperature IQ and IVBIAS vs Temperature (Sleep Mode) Unless otherwise specified the following conditions apply: Vin = Efficiency vs Load Current (500 kHz) 30067637 ...
Page 6
Startup Waveforms Load Transient Response UVLO Threshold vs Temperature (VDD = VIN) www.national.com Peak Current Limit vs Temperature 30067647 Normalized Switching Frequency vs Temperature (300kHz) 30067646 30067645 6 30067641 30067643 ...
Page 7
Block Diagram 7 30067603 www.national.com ...
Page 8
Operation Description GENERAL The LM26003 is a current mode PWM buck regulator. At the beginning of each clock cycle, the internal high-side switch turns on, allowing current to ramp-up in the inductor. The in- ductor current is internally monitored during ...
Page 9
Until the next cycle, the inductor current remains at zero. At nominal load currents, in FPWM mode, the device operates in continuous conduction mode, where ...
Page 10
Second, the inductor value can be increased to slow the current ramp and reduce the peak over-current. FREQUENCY ADJUSTMENT AND SYNCHRONIZATION The switching frequency of the LM26003 can ...
Page 11
FIGURE 6. Off-Pulse Skipping Waveforms Vin = 3.5V, Vnom = 3.3V, fnom = 305 kHz UVLO is sensed at both VIN and VDD, and is activated when either voltage falls below 2.96V (typical). Although VDD is typically less than 200 ...
Page 12
INDUCTOR The output inductor should be selected based on inductor ripple current. The amount of inductor ripple current com- pared to load current, or ripple content, is defined as Iripple/ Iload. Ripple content should be less than 40%. Inductor ripple ...
Page 13
BOOTSTRAP The drive voltage for the internal switch is supplied via the BOOT pin. This pin must be connected to a ceramic capacitor, Cboot, from the switch node, shown the typical ap- plication. The LM26003 provides the ...
Page 14
Where Co is the output capacitance the load resistance the output capacitor ESR, and fsw is the switching fre- quency. The effects of slope compensation and current sense gain are included in this equation. However, the ...
Page 15
A ceramic input capacitor must be connected as close as possible to the AVIN pin as well as PVIN pin. The capacitor between AVIN and ground should be grounded close to the GND pins of the LM26003 and the PVIN ...
Page 16
Physical Dimensions www.national.com inches (millimeters) unless otherwise noted eTSSOP-20 Package 20-Lead Exposed Pad TSSOP Package NS Package Number MXA20A 16 ...
Page 17
Notes 17 www.national.com ...
Page 18
... National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. ...